Echo PB-2620 Operator'S Manual Download Page 20 | Manualshive

Page: 20 / 52

background image

OPERATION

PB-2620

20

X7501190602

© 10/2017 ECHO Inc.

◆

Use an approved fuel container. Mark fuel containers as
containing 2-stroke mixture fuel.

◆

DO NOT smoke near fuel.

◆

DO NOT allow flames or sparks near fuel.

◆

Fuel tanks/cans may be under pressure. Always loosen
fuel caps slowly allowing pressure to equalize.

◆

NEVER refuel a unit when the engine is HOT or RUNNING!

◆

DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks
outdoors over bare ground.

◆

DO NOT overfill fuel tank. Wipe up spills immediately.

◆

Securely tighten fuel tank cap and close fuel container
after refueling.

◆

Inspect for fuel leakage. If fuel leakage is found, do not
start or operate unit until leakage is repaired.

◆

Move at least 3 m (10 ft.) from refueling location before
starting the engine.

Gasoline vapor is heavier than air, and can travel along the
ground to nearby sources of ignition such as electrical motors,
pilot lights, and hot or running engines. Vapors ignited by an
ignition source can flash back to the fuel container, resulting in
an explosion, fire, serious or fatal injuries, and extensive
property damage.

Mixing Instructions

1.

Fill an approved fuel container
with half of the required
amount of gasoline.

2.

Add the proper amount of
2-stroke oil to gasoline.

3.

Close container and shake to
mix oil with gasoline.

4.

Add remaining gasoline, close
fuel container, and remix.

Spilled fuel is a leading cause of hydrocarbon emissions. Some
locations may require the use of automatic fuel shut-off containers to
reduce fuel spillage.

Fuel to Oil Mix – 50:1 Ratio

US

Metric

Gas

Oil

Gas

Oil

gal.

fl.oz.

L

cc

1

2.6

5

100

2

5.2

10

200

5

13

25

500

«
...
18
19
20
21
22
...
»

Summary of Contents for PB-2620





















































Reviews:

No comments

Related manuals for PB-2620

Brand: Murray Pages: 44

Brand: Scheppach Pages: 116

Brand: Troy-Bilt Pages: 56

Wolf Garten Select SF Series

Brand: MTD Pages: 30

Brand: Okay Pages: 32

Brand: Stiga Pages: 26

Brand: Stiga Pages: 34

Brand: Maruyama Pages: 21

Brand: Maruyama Pages: 24

Brand: Desa Pages: 12

Brand: Talon Tools Pages: 3

Brand: Alpina Pages: 144

Brand: Snapper Pages: 18

PREMIUM 0503APESM1430

Brand: VALERII S&M GROUP Pages: 87

Brand: Columbia Pages: 36

Brand: Columbia Pages: 52

Brand: Troy-Bilt Pages: 48

PowerLok CCB410

Brand: Cub Cadet Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands