manualshive.com logo in svg

Echo PB-2620, Operator'S Manual, Page: 30 / 52

Share
Download
Echo PB-2620 Operator'S Manual Download Page 30

MAINTENANCE

PB-2620

30

X7501190602

© 10/2017 ECHO Inc.

• It is installed with the original side out.

5.

Install air filter cover.

Fuel Filter

Level 1.

Fuel is VERY flammable. Use extreme care when mixing, storing 
or handling, or serious personal injury may result.

1.

Use a clean rag to remove 
loose dirt from around fuel cap 
and empty fuel tank.

2.

Pull the fuel filter from the tank.

3.

Do not remove the wire coil 
clamp to remove the fuel filter. 
Pinch the fuel filter with the 
fingers on one hand and the 
fuel line with the other hand. 
Pull and twist slightly to 
separate.

4.

Install the new filter with the reverse action.

Note:  Federal EPA regulations require all model year 2012 and later 

gasoline powered engines produced for sale in the United 
States to be equipped with a special low permeation fuel 
supply hose between the carburetor and fuel tank. When 
servicing model year 2012 and later equipment, only fuel 
supply hoses certified by EPA can be used to replace the 
original equipment supply hose. Fines up to $37,500 may be 
enforced for using an un-certified replacement part.

Spark Plug

Level 2.

Use only NGK BPMR8Y spark plug otherwise severe engine damage 
may occur.

Parts Required:

Tune-Up Kit

Parts Required:

Tune-Up Kit

Summary of Contents for PB-2620





















































Reviews:

No comments