background image

H

EDGE

 C

LIPPER

O

PERATOR

'

S

 M

ANUAL

15

AIR

 

FILTER

Level 1.

Tools required:

25 or 50 mm (1 or 2 in.) medium bristle paint brush

Parts required:

90008 REPOWER

TM

 AIR & FUEL FILTER KIT

1.  Close choke (Cold Start Position). This prevents dirt from entering

the carburetor throat when the air filter is removed. Brush accumu-
lated dirt from the air cleaner area.

2. Remove the air cleaner cover. Clean and inspect the element for

damage.  If element is fuel soaked and very dirty, replace.

3. If element can be cleaned and reused, be certain it:

-still fits the cavity in the air cleaner cover.
-is installed with the original side out.

NOTE
Carburetor adjustment may be needed after air filter cleaning/
replacement.

FUEL

 

FILTER

Level 1.

Tools required: 200-250 mm  ( 8-10 in.) length of wire with one end

bent into a hook. Clean rag, funnel, and an approved
fuel container

Parts required:

90008 REPOWER

TM

 AIR & FUEL FILTER KIT

WARNING     

    DANGER

Fuel is VERY flammable. Use extreme care when mixing, storing or
handling.

1. Use a clean rag to remove loose dirt from around fuel cap and empty

fuel tank.

2. Use the “fuel line hook” to pull the fuel line and filter from the tank.

3. Remove the filter from the line and install the new filter.

Summary of Contents for HC-201

























Reviews: