background image

H

EDGE

 C

LIPPER

O

PERATOR

'

S

 M

ANUAL

3

Throughout this manual and on the product itself, you will find safety
alerts and helpful, information messages preceded by symbols or key
words.  The following is an explanation of those symbols and key words
and what they mean to you.

This symbol accompanied by the words WARNING and
DANGER calls attention to an act or condition that can lead to
serious personal injury to operator and bystanders.

The circle with the slash symbol means whatever is shown
within the circle is prohibited.

IMPORTANT
The enclosed message provides
information necessary for the protec-
tion of the unit.

NOTE
This enclosed message provides tips
for use, care and maintenance of the
unit.

M

ANUAL

 S

AFETY

 S

YMBOLS

 

AND

 I

MPORTANT

 I

NFORMATION

S

AFETY

DECALS

Locate these safety decals on your unit.  Make sure the decals are
legible and that you understand and follow the instructions on them.  If
a decal cannot be read, a new one can be ordered from your ECHO
dealer.  See PARTS ORDERING instructions for specific information.

P/N X505000270

P/N X5052242200

P/N 89016006361

Summary of Contents for HC-201

























Reviews: