background image

8

IMPORTANT

Stored fuel ages. Do not mix more fuel than
you expect to use in thirty (30) days, ninety
(90) days when a fuel stabilizer is added.
Stored two-stroke fuel may separate.
ALWAYS shake fuel container thoroughly
before each use.

On

Stop

Throttle trigger

NOTE

When engine does not stop, shift choke lever to
close position.
Check and repair ignition switch before starting
the engine again.

STARTING COLD ENGINE

STOPPING ENGINE

STARTING WARM ENGINE

Set throttle trigger in idle position.

Place ignition switch in STOP position.

Stand the engine upright on a level surface.

Place ignition switch in ON (START/RUN)
position.

Push purge bulb 3 to 4 times (or until fuel is
visible in fuel return line).

Shift choke lever to close position (START).

Pull starter handle until the engine fires.

Shift choke lever to full open position,and if
necessary, start the engine again and allow to
warm up before using.
- The clutch engages at approximately 3,500

r/min. Therefore the drill bit may rotate at fast
idle engine speed.

Choke lever

Place ignition switch in ON (START/RUN)
position.

Pull starter handle until the engine fires.
- Do not use the choke.

 (Open)

RUN

START

(Close)

Air cleaner

Fuel return line

Purge bulb

Starter handle

Push

Summary of Contents for ED-200

















Reviews: