background image

13

6. Drain the fuel tank completely and pull the

recoil starter handle several times to remove
fuel from the carburetor.

7. Remove the spark plug and pour 1/2

tablespoon (1/4 oz) of fresh, clean, 2-stroke
engine oil into the cylinder through the spark
plug hole.

A. Place a clean cloth over the spark plug hole.

B. Pull the recoil starter handle 2 or 3 times to

distribute the oil inside the engine.

C. Observe the piston location through the

spark plug hole. Pull the recoil starter handle
slowly until the piston reaches the top of its
travel and leave it there.

8. Install the spark plug (do not connect ignition

cable.)

9. Lubricate the drill bit with a heavy coat of oil to

prevent rust.

NOTE

For future reference, you should keep this
operator’s manual.

STORAGE

LONG TERM  STORAGE
(Over 30 Days)

Do not store your unit for a prolonged period of
time (30 days or longer) without performing
protective storage maintenance which includes the
following:

1. Store unit in a dry, dust free place, out of the

reach of children.

2. Place the ignition switch in the STOP position.

3. Remove accumulation of grease, oil, dirt and

debris from exterior of unit.

4. Perform all periodic lubrication and services

that are required.

5. Tighten all the screws and nuts.

WARNING         DANGER

DO NOT STORE IN ENCLOSURE WHERE
FUEL FUMES MAY ACCUMULATE OR
REACH AN OPEN FLAME OR SPARK.

CLEANING SILENCER AND
EXHAUST PORT
 
(Check Periodically)

1. Carefully remove housing halves.

2. Remove and disassemble silencer.

NOTE

Be careful not to scratch the cylinder or piston
when cleaning the cylinder exhaust port.

3. Clean deposits from cylinder exhaust port and

silencer.

CLEANING CYLINDER FINS
(Check Periodically)

NOTE

Clogged fins will cause poor engine cooling.

1. Carefully remove housing and clean dirt and

dust from fins.

2. Reinstall housing.

Summary of Contents for ED-200

















Reviews: