background image

20

muffleR

 

spaRk

 

aRRestoR

IMPORTANT

  

Carbon deposits in muffler will cause a drop in engine 

output and overheating.  Spark arrestor screen must be 

checked periodically.

 1.  Remove  muffler cover. 

 2.  Remove spark arrestor screen cover, gaskets, and 

screen from muffler body. 

 3.  Clean carbon deposits from muffler components.

NOTE

When cleaning carbon deposit, be careful not to damage 

the catalytic element inside muffler.

 4.  Replace screen if it is cracked, plugged, or has holes 

burned through. 

 5.  Assemble components in reverse order.  

CoolinG

 

system

 

CleaninG

•  Remove spark plug lead.

•  Remove two (2) muffler cover screws and muffler cover.

•  Remove four (4) recoil starter housing screws and starter 

housing.

•  Use a stiff bristle cleaning brush (do not us a metal 

brush) to remove dirt from cylinder fins in muffler and 

ignition coil areas.

Cylinder Exhaust Port

IMPORTANT

The cylinder exhaust port must be inspected and cleaned 

of excess carbon every 3 months or 90 hours of opera-

tion in order to maintain this engine within the emissions 

durability period. ECHO strongly recommends that you 

return your unit to your ECHO dealer for this important 

maintenance service.

Summary of Contents for CS-301





























Reviews: