manualshive.com logo in svg

Echo CS-301, Instruction Manual, Page: 26 / 28

Share
Download
Echo CS-301 Instruction Manual Download Page 26

26

TESTING THE BRAKE

•  Start the engine on a solid level surface and run at a fast 

idle until warm.

•  Hold the saw firmly by the handles and accelerate the en

-

gine to a fast idle.

•  Slowly operate the chain brake lever while holding the saw 

firmly on the ground. When the brake lever trips, the chain 

should stop. Immediately release the throttle  trigger.

IMPORTANT

Do not allow the saw to tip forward in order to 

avoid damage to the chain.

If the chain does not stop, immediately return the saw to your 

authorized Echo dealer for repair.

INSTALLATION

•  Echo recommends that the chain brake should be serviced 

by an authorized Echo servicing dealer.

OPERATION

•  Set the lever in the 

unlocked position before starting to cut.

•  If the brake is tripped by kick back reaction, the chain will 

stop. Immediately release the throttle to avoid possible 

damage to the engine or clutch.

•  Do not attempt to operate the engine with the brake 

locked.

•  When the lever is fully pulled toward the operator, brake is 

unlocked.

Summary of Contents for CS-301





























Reviews:

No comments