manualshive.com logo in svg

Echo CS-301, Instruction Manual, Page: 3 / 28

Share
Download
Echo CS-301 Instruction Manual Download Page 3

3

9.   Carry the chain saw with the engine stopped, 

the guide bar and saw chain to the rear, and 

the muffler away from your body.

10. Do not operate a chain saw that is damaged, 

improperly adjusted, or not completely and 

securely assembled. Be sure that the saw 

chain stops moving when the throttle control 

trigger is released.

11. Shut off the engine before setting the chain 

saw down.

12. Use extreme caution when cutting small size 

brush and saplings because slender material 

may catch the saw chain and be whipped 

toward you or pull you off balance.

13. When cutting a limb that is under tension, be 

alert for spring back so that you will not be 

struck when the tension in the wood fibers is 

released.

14. Keep the handles dry, clean, and free of oil 

or fuel mixture.

15. Operate the chain saw only in well-ventilated 

areas.

16. Do not operate a chain saw in a tree unless 

you have been specifically trained to do so.

17. All chain saw service, other than the items 

listed in the Instruction Manual mainte-

nance instructions, should be performed 

by competent chain saw service personnel. 

(For example, if improper tools are used to 

remove the flywheel or if an improper tool is 

used to hold the flywheel in order to remove 

the clutch, structural damage to the flywheel 

could occur and could subsequently cause 

the flywheel to burst.)

18. When transporting your  chain saw, use the 

appropriate guide bar scabbard.

19. Spark  arrestor  mufflers  approved  to  SAE 

Standard J335b are Standard on ECHO 

Chain saws to reduce the possibility of for-

est fires. Do not operate the chain saw with 

a loose or defective muffler. Do not remove 

the spark arrestor screen.

WARNING  

  DANGER

• 

During operation, the muffler or catalytic muffler and surrounding cover become hot.

• 

Never suspend the saw on a lanyard with the engine running.

• 

Always use the saw from the right-hand side of your body – 

NEVER

 from the left side.

• 

Always wear proper safety clothing to protect your lower body from sharp saw chain and 

hot muffler.

• 

Always keep exhaust area clear of flammable debris during transportation or when storing, 

otherwise serious property damage or personal injury may result.

WARNING  

  DANGER

  Using improper replacement components or removing safety devices may result in serious or fatal injury.

Summary of Contents for CS-301





























Reviews:

No comments