manualshive.com logo in svg

Echo CS-301, Instruction Manual, Page: 9 / 28

Share
Download
Echo CS-301 Instruction Manual Download Page 9

9

 

WARNING

IMPROPER CLUTCH COVER ASSEMBLY CAN RE-

SULT IN SERIOUS INJURY, AND WILL CAUSE SE-

VERE SAW DAMAGE IF UNIT IS STARTED. NEVER 

START OR OPERATE SAW IF BRAKE BAND IS NOT 

IN PLACE ON CLUTCH DRUM. ALWAYS CHECK 

CHAIN BRAKE OPERATION AFTER REPLACING 

COVER. DO NOT USE SAW IF CHAIN BRAKE DOES 

NOT FUNCTION PROPERLY.

p

RepaRation

 

foR

 u

se

H

I

J

7.  Turn saw over and check brake band for correct posi-

tion around clutch drum. If brake band is not in place 

around drum, remove clutch cover, make sure brake is 

released, and reinstall.

CAUTION!

•  When starting, idling adjustment speed should be adjusted not to rotate the saw chain.

•  When there is trouble with the carburetor, refer to your distributor or dealer.

kiCk

 

GuaRD

® 

to

 

baR

 

instRuCtions

For saws with Kick Guard

®

 P/N 2894901 and symmetri-

cal or asymmetrical low-kick type guide bars.

 

1.  Install bolt (A) in 

rear

 hole (B) of Kick Guard

®

 and 

through front hole (C) in guide bar.

 2. 

IMPORTANT:

 Dimple in Kick Guard

®

 (D) must engage 

recess in guide bar (E).

 

3.  Tighten nut (F) and bolt (A) until snug. Make certain 

Kick Guard

®

 is flush against guide bar.

GuiDe

 

baR

 

anD

 

saw

 

Chain

-

install

/

Remove

WARNING  

  DANGER

Saw Chain is sharp! Always wear gloves when handling 

assembly, otherwise serious personal injury may result.

NOTE

Move chain brake lever fully rearward to remove or install 

clutch cover  to saw.

IMPORTANT

Always loosen guide bar nuts before turning chain 

tension adjuster, otherwise clutch cover and tensioner 

will be damaged.

1.  Remove spark plug lead.

2.  Remove two guide bar nuts and remove guide bar cover. 

Turn tension adjustment screw counterclockwise 2 to 3 
turns if bar and chain are installed.

3.

 

Remove guide bar and saw chain if necessary.

NOTE: 

See “MAINTENANCE AND CARE” instructions  

for guide bar, sprocket, and saw chain maintenance.

4.  Mount guide bar (G) on studs, and slide toward sprocket 

to make saw chain installation easier.

5.  Install saw chain (H) as shown, with cutters on top of 

guide bar facing forward.

6.  Align holes of clutch cover (J) with guide bar studs, 

and tensioner pin (I) with lower guide bar adjuster hole. 

Summary of Contents for CS-301





























Reviews:

No comments