EBS CPX200NB Installation And Programming Manual Download

Page: 11 / 116

CPX200NB ALARM CONTROL UNIT – INSTALLER MANUAL

11 / 116

Green “OK” LED

For the detailed description of “OK” LED operation, please refer to chapter 9.

Connector of “CONF” Programming Device

“CONF” IDC10 connector allows the control unit configuration using dedicated

GD-PROG

programming device and any computer equipped with RS232 port.

“PROG” Button for Default Settings Restoration

Pressing the button for 10s during connecting the control unit with power supply will delete
all users and restore the default admin and instaler code. Default admin code is 1111,

defoult instaler code is 2222.

“START” Button for Battery Activation of Control Unit Without the Mains
Power Supply

If the control unit is activated in the situation of power supply fault, press the button after
connecting the unit to the battery.

Screwed Connectors of the Control Unit

For detailed information on feeding, input and output connectors, please refer to chapter
3.3.

10.

Assembly Holes of the Control Unit (132x61mm hole span)

The above holes are intended for the control unit to be assembled in any type of casing. In

option a dedicated plastic

OBDNA

casing can be ordered (the casing includes appropriate

230VAC/18VAC transformer).

Summary of Contents for CPX200NB





















































































































Search results

Summary of Contents for CPX200NB

Reviews:

Related manuals for CPX200NB

Brands by name

Popular brands

EBS CPX200NB, Installation And Programming Manual

Search results

Summary of Contents for CPX200NB

Reviews:

Related manuals for CPX200NB

Brands by name

Popular brands