background image

13

Instruction Booklet 

IB019013EN

Effective March 2019

Zone selective interlocking test kit 

For Digitrip 520M, 520MC and 1150 trip units 

  

EATON

 www.eaton.com

ZSI breaker testing work sheet Digitrip 1150+

The following are the test settings used while programming the 1150+ Digitrip unit. If a parameter setting does not match the one required 

for testing, record it in the space provided, and then modify the setting to match the chart. After testing, remember to change your settings 

back to the states you record below. 

Setting (required for testing)            Original setting

Setting (required for testing)             Original setting

Curve type (LSIG**) ____________________________________

Ground slope** (flat) ____________________________________

Long slope (I

2

T) ________________________________________

Ground time (0.30 sec) __________________________________

Long PU (0.4 sec) ______________________________________

Amp unbalance (off) ____________________________________

Long time @ 6 X Ir (2.0 sec) _____________________________

Amp unbalance time (10 sec) ____________________________

Long memory (off)  _____________________________________

Phase loss (off)  ________________________________________

Short slope (flat)________________________________________

Main PU (10 x 

l

n

) _______________________________________

Short PU (3.0 x 

l

r

) _______________________________________

Maintenance mode (disabled) ____________________________

Short time Z1* (0.50 sec) ________________________________

Frequency (60 Hz) ______________________________________

Short time Z2* (0.30 sec) _______________________________

BC relay reset (auto) ____________________________________

Short time Z3* (0.10 sec) ________________________________

Sliding demand (off) ____________________________________

Inst PU (4 x 

l

n

) __________________________________________

Wave form capture (off) _________________________________

Gnd PU (0.3) ___________________________________________

Rev power sensing (disabled) ____________________________

                                                                          Breaker name: __________ Breaker position: ___________

Setting (required for testing)             Original setting

Setting (required for testing)             Original setting

Curve type (LSIG**) ____________________________________

Ground slope** (flat) ____________________________________

Long slope (I

2

T) ________________________________________

Ground time (0.30 sec) __________________________________

Long PU (0.4 sec) ______________________________________

Amp unbalance (off) ____________________________________

Long time @ 6 X Ir (2.0 sec) _____________________________

Amp unbalance time (10 sec) ____________________________

Long memory (off)  _____________________________________

Phase loss (off)  ________________________________________

Short slope (flat)________________________________________

Main PU (10 x 

l

n

) _______________________________________

Short PU (3.0 x 

l

r

) _______________________________________

Maintenance mode (disabled) ____________________________

Short time Z1* (0.50 sec) ________________________________

Frequency (60 Hz) ______________________________________

Short time Z2* (0.30 sec) _______________________________

BC relay reset (auto) ____________________________________

Short time Z3* (0.10 sec) ________________________________

Sliding demand (off) ____________________________________

Inst PU (4 x 

l

n

) __________________________________________

Wave form capture (off) _________________________________

Gnd PU (0.3) ___________________________________________

Rev power sensing (disabled) ____________________________

                                                           

Breaker name: __________ Breaker position: __________

_

*  Assuming Z1 is connected to main, Z2 is directly downstream of Z1, and Z3 is directly downstream of Z2.
**  If supplied.

Summary of Contents for ZSI















Reviews: