background image

5

Instruction Booklet 

IB019013EN

Effective March 2019

Zone selective interlocking test kit 

For Digitrip 520M, 520MC and 1150 trip units 

  

EATON

 www.eaton.com

Zone configurations 

The figures below depict some of the most common ZSI wiring schemes.  These configurations 

describe how to connect the ZSI plugs to the breakers to be tested and where each zone plug should be 

connected to the corresponding receptacle on the test box. The table below each figure describes the 

ZSI wiring scheme configuration and what the ZSI test box is testing on each configuration based on the 

selections made on the HMI. Circuit diagrams of these setups can be found in the “Zone Config” screen 

subsection of the “Navigating the HMI Screens” section in this manual.

otee:

N

For M-T-T-M, repeat test for each tie breaker.

ZSI

Test

Box

Zone 1

Zone 2

Zone 3

Main1 Digitrip

Tie Digitrip

Main2 Feeder Digitrip

Configuration 1

Main Tie Main

Configuration 1
Arrangement 

double

Main fault:  This simulates a fault originating 

between the M1 (main 1) breaker and the tie 

breaker

Tie fault:  This simulates a fault on originating 

downstream of the M1 (main 1) breaker and 

the tie breaker.

Feeder fault:  This simulates a fault originating 

on the load side of a feeder on the main 2 bus 

(main 2 feeder).  This fault would flow through 

main 1, the tie breaker, and the main 2 feeder 

breaker.

Summary of Contents for ZSI















Reviews: