
xChargeIn
Introduction
Operating instructions V1.04
103
© EATON
1.2
Purpose of the document
This document describes the operation of xChargeIn.
1.3
Requirements
This document contains information for people who want to operate a charg-
ing station.
1.4
Intended use
The charging station is intended for charging electric vehicles (such as elec-
tric cars). The connection of other devices (such as power tools) is not al-
lowed.
The charging station is suitable for indoor and outdoor use. The charging
station has to be installed vertically on a wall or on a floor-mounted column.
The surface for the installation must be flat and suitably stable (e.g. brick
wall, concrete wall). The respective national regulations must be observed
with regard to the installation and connection of the charging station.
The intended use of the device always includes the compliance with the en-
vironmental conditions for which this device was developed.
The charging station has been developed, manufactured, tested and docu-
mented in accordance with the appropriate safety standards. If the instruc-
tions and safety instructions described for the intended use are observed,
the product will normally not pose a risk to the health of persons or damage
to property.
Not observing the safety instructions can result in risk of death, in-
juries and damage to the device!
The device manufacturer assumes no liability for resulting claims!
1.5
Warranty
Only general maintenance work that is expressly permitted by Eaton may be
performed. Any other tampering to the device will result in a loss of the war-
ranty claim.
A device with broken manufacturer's seals or removed lead seals may no
longer be put into operation. The necessary steps for replacement of the
charging station by the specialist dealer or service partner must be initiated.
1.6
Notes on this document
The manual is part of the product. It is to be retained over the entire life cycle
of the product and should be forwarded to any subsequent owners or users
of the product.
Summary of Contents for xChargeIn A Series
