Eaton PowerXL DH1 Applications Manual Download Page 112

Page: 112 / 240

POWERXL DH1 SERIES ADJUSTABLE FREQUENCY DRIVES

MN040041EN—August 2019 www.eaton.com

Chapter 6 — PID Application

Table 127. BACnet MS/TP — P12.3.3

Code

Parameter

Min.

Max.

Unit

Default

Note

P12.3.3.1

MSTP Baud Rate

594

0 = 9600
1 = 19200
2 = 38400
3 = 76800
4 = 115200

P12.3.3.2

MSTP Device Address

127

595

P12.3.3.3

MSTP Instance Number

4194302

Varies

596

P12.3.3.4

MSTP Comm Timeout

60000

10000

598

P12.3.3.5

MSTP Protocol Status

599

0 = Stopped
1 = Operational
2 = Faulted

P12.3.3.6

MSTP Fault Code

600

0 = None
1 = Sole Master

P12.3.3.7

MSTP Fault Response

2526

See Par ID 2516

P12.3.3.8

MSTP Max Master

127

1537

EtherNet Bus

Table 128. Basic Setting — P12.4.1

Code

Parameter

Min.

Max.

Unit

Default

Note

P12.4.1.1

IP Address Mode

1500

0 = Static IP
1 = DHCP with AutoIP

P12.4.1.2

Active IP Address

1507

P12.4.1.3

Active Subnet Mask

1509

P12.4.1.4

Active Default Gateway

1511

P12.4.1.5

MAC Address

1513

P12.4.1.6

Static IP Address

192.168.1.254

1501

P12.4.1.7

Static Subnet Mask

255.255.255.0

1503

P12.4.1.8

Static Default Gateway

192.168.1.1

1505

P12.4.1.9

Enable BACnetIP

1725

See Par ID 1346

Table 129. Modbus TCP — P12.4.2

Code

Parameter

Min.

Max.

Unit

Default

Note

P12.4.2.1

Connection Limit

609

P12.4.2.2

Modbus TCP Unit ID

610

P12.4.2.3

Comm Timeout Modbus TCP

60000

10000

611

P12.4.2.4

Modbus TCP Protocol Status

612

See Par ID 599

P12.4.2.5

Modbus TCP Fault Response

2517

See Par ID 2516

P12.4.2.6

Modbus TCP Trusted IP Enable

See Par ID 1346

P12.4.2.7

Trusted IP White List

0xC0.0xA8.
0x01.0xFF.
0x00.0x00.
0x00.0x00.
0x00.0x00.
0x00.0x00

ote:

Parameter value can only be changed after the drive has stopped.

Parameter value will be set to be default when changing macros.

Input function is Level sensed.

Summary of Contents for PowerXL DH1

















































































































































































































































Search results

Summary of Contents for PowerXL DH1

Reviews:

Brands by name

Popular brands

Eaton PowerXL DH1, Applications Manual

Search results

Summary of Contents for PowerXL DH1

Reviews:

Brands by name

Popular brands