Eaton EPCT Fire Series, Installation Manual

Page: 18 / 59

11
Programming
EPCT FirE sEriEs FirE PumP ConTrollEr
MN124016EN August 2019 www.eaton.com
5.0 Programming
5.1 Introduction
The EPCT controller is fully programmable from the device’s
faceplate. Users can program set points as well as other
parameters. The time, date, and set points can only be
changed from the menu system.
The menu system is broken down to tab systems. These
include, Home, Startup, Panel Setup, Help, Pressure
Settings, Timer Values, ATS Settings (if equipped), Alarm
Setpoints, Inputs/Outputs, History/Statistics/Diagnostics,
and Optional Output Card(s) (if equipped).
5.2 Navigation
In order to navigate through the EPCT operating system,
press the tabs at the top of the screen to go through the
menu. If the main menu password is enabled, the user will
be prompted to enter the password to access any of the
tabs except for Help and History/Statistics/Diagnostics.
NOTICE
It is recommended to set up a main menu password to help
prevent any unauthorized access to the controller. This will
help prevent reprogramming the controller that will impede
the operation of the fire pump controller.
The controller does come with the ability to “Lockout” the
display after thirty (30) minutes of inactivity to minimize
accidental inputs. This feature will not inhibit the normal
operation of the controller. To unlock the display, the user
will be prompted to enter in “EPCT”.
In order to increase the longevity of the display board,
the controller will activate the screensaver after thirty (30)
minutes of inactivity. The screen saver will turn the screen
black and will show a moving EATON logo. To deactivate the
screensaver simply press anywhere on the screen.
All EPCT controller programmable features and associated
set-point possibilities are presented in Table 1.
Table 1
Description range
Panel setup
Language English / French / Spanish / Portuguese / Turkish
/ Italian / Polish / Simplified Chinese / Dutch
Set time 24 Hours
Set date Any valid date
Set day of the week Any valid day of the week
Starting method Across the Line / Part Winding / Primary
Resistor / Autotransformer/ WYE-Delta Open /
Wye-Delta Close / Soft Start
Single phase start Enabled / Disabled
Auto shutdown Enabled / Disabled
Motor HP 0-9999 HP
Nominal voltage 200-7200V
Phases Single Phase / Three Phase
Description range
System Frequency 50Hz / 60Hz
CT Ratio 50:0.1 / 100:0.1 / 150:0.1 / 300:0.1 / 500:0.1 /
800:0.1 / 1200:0.1
Motor FLA 1-999 A
Foam Controller Enabled / Disabled
Menu Password One (1) to seven (7) digit numeric / Disabled
Controller Serial Number Standard keyboard entry with space for fifty (50)
digits - Numeric and/or Alphabetical -
Pump Serial Number Standard keyboard entry with space for fifty (50)
digits - Numeric and/or Alphabetical
Screen Brightness 20%, 40%, 60%, 80%, 100%
Enable Welcome Screen Enabled / Disabled
Screen Lock Enable/Disable
Customer service contact
Enable Password Protection One (1) to seven (7) digit numeric / Disabled
Company Name
Standard keyboard entry with space for fifty (50)
digits - Numeric and/or Alphabetical
Contact Name Standard keyboard entry with space for fifty (50)
digits - Numeric and/or Alphabetical
Phone Number Numeric entry with space for 15 digits
Email Standard keyboard entry with space for fifty (50)
digits - Numeric and/or Alphabetical
service message trigger
Number of Hours Run 1-999 Hour
Number of Starts 1-999 Pump Runs
Specific Time and Date 24 Hours - Any valid date
De-energize Common Alarm Enabled / Disabled
Pressure settings
Start Pressure 0-999 PSI / Disabled
Stop Pressure 0-999 PSI / Disabled
Low Pressure Alarm 0-999 PSI / Disabled
High Pressure Alarm 0-999 PSI / Disabled
Start Above Pressure 0-999 PSI / Disabled
Pressure Variance Recording 1-999 PSI / Disabled
Hourly Pressure Recording
Enabled / Disabled
low suction shutdown Enabled / Disabled
Shutdown Delay 0-99 Seconds / Disabled
Reset Mode Automatic / Manual
Automatic Reset Delay 0-99 Seconds / Disabled
low foam shutdown Enabled / Disabled
Shutdown Delay 0-99 Seconds / Disabled
Reset Mode Automatic / Manual
Automatic Reset Delay 0-99 Seconds / Disabled
Proof Pressure Switch Enabled / Disabled
Pressure Units PSI / BAR / kPa
Pressure Transducer Enabled / Disabled
Calibrate Pressure
Transducer
Calibrate Using 0 PSI / Calibrate Using Current
Pressure / Reset to Factory Default
Timer values
Minimum Run Time Four (4) digit numeric entry in Minutes:
Seconds / Disabled
Acceleration Timer 0-10 seconds / Disabled
Sequential Start Timer 0-999 seconds / Disabled
Fail to Start Timer 0-999 seconds / Disabled