background image

18

Programming

DPCT IOM InsTruCTIOn OPeraTIOn Manual

   MN124018EN   January 2023   www.eaton.com

The SST will not work on Remote Manual Starts or Local 

Manual Starts.

5.7.3  AC power failure alarm

If AC power is lost and this setting is ENABLED the 

controller will start timing the programmed timer. Once 

the timer has elapsed and if AC power is still absent the 

controller will alarm for AC POWER FAILURE and trigger the 

COMMON ALARM.

5.7.4  AC power failure start

If this is ENABLED and the AC power failure alarm is triggered 

the controller will start the engine automatically until either it is 

manually shut down or AC power has returned.

 

5.7.5  Weekly engine test timer

A Weekly Engine Test Timer can be programmed that 

will automatically start and run the fire pump engine at 

specific intervals. The Weekly Timer is set by adjusting 

the day, hour, and minute of the desired weekly run time, 

the length of time that this test shall be performed, and 

a test interval (in weeks). While the weekly test timer 

is timing, the remaining time will be displayed in the 

notification area.

5.8  Alarm setpoints tab

5.8.1  Source voltage alarm setpoint

This menu item allows the user to adjust the source voltage 

dropout and pickup settings. 

5.8.2  Battery voltage alarm setpoint

This menu item allows the user to adjust the battery voltage 

dropout and pickup settings. 

5.8.3  Transducer fail pump start

Transducer Failure is defined as the transducer reading is 

lower than 4mA or greater than 20mA. If this setting is 

enabled and the transducer reading is out of the allowable 

range, the controller will start the engine and alarm for 

Transducer Failure.

5.8.4  Abort engine test

When enabled, this will cause the controller to abort the 

engine test when selected settings are enabled. These 

settings are: Low Oil Pressure, High Engine Temperature, 

ECM in Alternate, Fuel Injector Malfunction, ECM 

Warning, ECM Failure, High Raw Water Temp, Low Raw 

Water Flow, or Low Engine Temperature. 

5.9  Inputs/outputs tab

5.9.1  Inputs

The optional inputs have the ability to be programmed for 

predetermined values or custom values. The Input menu 

will display each input, what it is programmed for, allow a 

delay to be programmed, allow the input to latch when the 

input signal is received, program the input to be fail safe (if 

enabled, the contact will be considered normally closed) 

and link the notification area virtual indicators to the input. 

Refer to Table 3 Programmable Input Alarms for the generic 

values the optional inputs can be programmed for. When 

this input is received a message will be stored in memory 

using the programmed label. The input can be linked to the 

common alarm under the Panel Setup menu. 

Table 3. 

DPCT Programmable Input alarms

Programmable input alarms

Remote Manual Start
Remote Manual Stop
Remote Manual Start/Stop
Remote Auto Start
Deluge Valve Start
Low Fuel
High Fuel
Fuel Spill
Low Suction
Low Foam Level
Proof Pressure Switch
Dump Valve
Low Room Temp
High Room Temp
Low Reservoir
High Reservoir
Reservoir Empty
Interlock
Enable Sequential Start
Relief Valve Discharge
Custom Input
Undefined

5.9.2  Outputs

The optional output relays can be programmed to operate 

based on the desired function. The Custom Output 

menu will display each output, what it is programmed 

for, allow a delay to be programmed, allow the output 

to latch when the relay is energized, and program the 

output for fail safe (if enabled, the relay will be normally 

energized). Please refer to Table 

4

 Programmable Output 

Alarms for the generic values the optional outputs can be 

programmed for. 

Summary of Contents for DPCT

































































Reviews: