background image

ii

Instruction Book    IB182312EN   June 2016   www.eaton.com

50/75/150 VCP-W

Selectable Ground and Test Device

 WARNING

IMPROPERLY INSTALLING OR MAINTAINING THESE PRODUCTS CAN 

RESULT IN DEATH, SERIOUS PERSONAL INJURY OR PROPERTY DAMAGE.

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE ATTEMPTING 

ANY UNPACKING, ASSEMBLY, OPERATION OR MAINTENANCE OF THE 

SELECTABLE GROUND AND TEST DEVICES.

INSTALLATION OR MAINTENANCE SHOULD BE ATTEMPTED ONLY 

BY QUALIFIED PERSONNEL. THIS INSTRUCTION BOOK SHOULD NOT 

BE CONSIDERED ALL INCLUSIVE REGARDING INSTALLATION OR 

MAINTENANCE PROCEDURES. IF FURTHER INFORMATION IS REQUIRED, 

YOU SHOULD CONSULT EATON’S ELECTRICAL SERVICES & SYSTEMS.

THE SELECTABLE GROUND AND TEST DEVICES DESCRIBED IN THIS BOOK 

ARE DESIGNED AND TESTED TO OPERATE WITHIN THEIR NAMEPLATE 

RATINGS. OPERATION OUTSIDE OF THESE RATINGS MAY CAUSE THE 

EQUIPMENT TO FAIL, RESULTING IN DEATH, BODILY INJURY AND 

PROPERTY DAMAGE.

ALL APPLICABLE CODES, SAFETY STANDARDS AND/OR REGULATIONS 

RELATED TO THIS TYPE OF EQUIPMENT MUST BE STRICTLY FOLLOWED.

THESE SELECTABLE GROUND AND TEST DEVICES ARE DESIGNED TO 

BE INSTALLED PURSUANT TO THE AMERICAN NATIONAL STANDARDS 

INSTITUTE (ANSI). SERIOUS INJURY, INCLUDING DEATH, CAN RESULT 

FROM FAILURE TO FOLLOW THE PROCEDURES OUTLINED IN THIS 

MANUAL.

DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY

The information, recommendations, descriptions and safety notations in this document are based on Eaton’s experience and judgment and 

may not cover all contingencies. If further information is required, an Eaton sales office should be consulted. Sale of the product shown in 

this literature is subject to the terms and conditions outlined in appropriate Eaton selling policies or other contractual agreement between 

Eaton and the purchaser.
THERE ARE NO UNDERSTANDINGS, AGREEMENTS, WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF FITNESS 

FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, OTHER THAN THOSE SPECIFICALLY SET OUT IN ANY EXISTING CONTRACT 

BETWEEN THE PARTIES. ANY SUCH CONTRACT STATES THE ENTIRE OBLIGATION OF EATON. THE CONTENTS OF THIS DOCUMENT 

SHALL NOT BECOME PART OF OR MODIFY ANY CONTRACT BETWEEN THE PARTIES. 
In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or other-wise for any 

special, indirect, incidental or consequential damage or loss whatsoever, including but not limited to damage or loss of use of equipment, 

plant or power system, cost of capital, loss of power, additional expenses in the use of existing power facilities, or claims against the 

purchaser or user by its customers resulting from the use of the information, recommendations and descriptions contained herein. The 

information contained in this manual is subject to change without notice. 

This product was manufactured by Eaton at the Power Breaker 

Center (PBC): 310 Maxwell Avenue, Greenwood, SC 29646.
All possible contingencies which may arise during installation, 

operation or maintenance, and all details and variations of this 

equipment do not purport to be covered by these instructions. If 

further information is desired by purchaser regarding his particular 

installation, operation or maintenance of particular equipment, 

contact an Eaton representative.

Summary of Contents for 150 VCP-W-SGT





















Reviews: