background image

 

17 

 

EASYGATE will at this option repair or replace out-of-warranty products which are returned to its factory 

according to the following conditions. Anyone returning goods to EASYGATE must first obtain an 
authorization number. EASYGATE will not accept any shipment whatsoever for which prior authorization 

has not been obtained. Products which EASYGATE determine to be repairable will be repaired and 

returned. A set fee which EASYGATE have been predetermined and which may be revised from time to 

time will be charged for each unit repaired. Products which EASYGATE determines not repairable will be 
replaced by the nearest equivalent product available at that time. The current market price for the 

replacement product will be charged for each replacement unit. 

International Warranty:

 

EASYGATE shall not be responsible for any customs fees, taxes, or VAT that may be due. 

WARNING 

Please Read Carefully

 

Important Notice:

 

An auto gate system cannot prevent burglary. It is only a replacement way for user to open the door. 
Auto gate systems are generally very reliable but they may not work under all conditions and they are 
not a substitute for prudent security practices or life and property insurance. Your auto gate system 

should be installed and serviced by qualified security professionals who should instruct you on the level 

of protection that has been provided and on the system operations. 

Note to Installers:

 

This warning contains vital information. As the only individual in contact with systems user, it is your 

responsibility to bring each item in this warning to the attention of the users of this system. 

 

System Failures:

 

This system has been carefully designed to be as effective as possible. There are circumstances, 

however, involving fire, burglary, or other types of emergencies where it may not provide protection. 

Any auto gate system of any type may be compromised deliberately or may fail to operate as expected 

for a variety of reasons. Some but not all of these reasons may be: 

Inadequate Installation:

 

A security system must be installed properly in order to provide adequate protection. Every installation 

should be evaluated by a security professional to ensure that all measurement is correct. Gates must be 

level and move freely and consistently in both open and closing cycle. 

Power Failure:

 

Control units require an adequate power supply for proper operation. If a device operates from batteries, 

it is possible for the batteries to fail. Even if the batteries have not failed, they must be charged, in good 

condition and installed correctly. If a device operates only by AC power, any interruption, however brief, 

will render that device inoperative while it does not have power. Power interruptions of any length are 

often accompanied by voltage fluctuations which may damage electronic equipment such as security 

system. After a power interruption has occurred, immediately conduct a complete system test to ensure 

that the system operates as intended. 

Short circuiting of components:

 

Take care when adjusting any part of the system. Always remove power to the control board and other 

devices when working on them. Never change/remove/cut/disconnect or other alteration with power 

connected either via the transformer or the batteries. Short circuiting components is not covered under 

this warranty. 

Failure of Replaceable Batteries:

 

Summary of Contents for Terrier 200



















Reviews: