EASTMAN Kodak X-Omat 3000 RA PROCESSOR Adjustments Download Page 46

Page: 46 / 88

ADJUSTMENTS AND REPLACEMENTS

01JUN99 – 5B6331

Removing the HEAT EXCHANGER

Warning

Dangerous Voltage

[1] De-energize the PROCESSOR.

[2] Lift the TOP COVER.

[3] Remove:

• DRIVE END PANEL

• WET SECTION COVER

• EXIT RACK

• DRYER RACK

[4] Install 2 CLAMPS TL-2170 on the HEAT EXCHANGER FORMED TUBING.

[5] Remove the 2 HOSE CLAMPS on the HEAT EXCHANGER FORMED TUBING.

[6] Remove:

• FORMED TUBING from the ends of the BARBED FITTINGS

• BARBED FITTINGS from the HEAT EXCHANGER

• O-RING SEALS

• HEAT EXCHANGER from the WASH TANK

H150_0150HA

H150_0150HCA

HOSE CLAMP

BARBED FITTING

O-RING SEAL

EXCHANGER

HEAT

FORMED TUBING

Summary of Contents for Kodak X-Omat 3000 RA PROCESSOR

























































































Search results

Summary of Contents for Kodak X-Omat 3000 RA PROCESSOR

Reviews:

Related manuals for Kodak X-Omat 3000 RA PROCESSOR

Brands by name

Popular brands

EASTMAN Kodak X-Omat 3000 RA PROCESSOR, Adjustments

Search results

Summary of Contents for Kodak X-Omat 3000 RA PROCESSOR

Reviews:

Related manuals for Kodak X-Omat 3000 RA PROCESSOR

Brands by name

Popular brands