EASTMAN Kodak X-Omat 3000 RA PROCESSOR Adjustments Download Page 29

Page: 29 / 88

MAIN DRIVE

5B6331 – 01JUN99

Removing the DRIVE MOTOR B6 and the GEAR BOX

Warning

Dangerous Voltage

[1] De-energize the PROCESSOR.

[2] Lift the TOP COVER.

[3] Remove:

• DRIVE SIDE PANEL

• DRYER END PANEL

• DRIVE CHAIN COVER by removing the 3 SCREWS

[4] Loosen the 4 DRIVE MOTOR BOLTS from the MOTOR BRACKET.

[5] Lift the DRIVE MOTOR and remove the DRIVE CHAIN.

[6] Remove the SPROCKET from the DRIVE MOTOR by loosening the SETSCREW.

H150_0130HA

SETSCREW

MOTOR

3 WASHERS

3 LOCK WASHERS

3 SCREWS

SPROCKET

DRIVE SHAFT

MOTOR

4 DRIVE

BOLTS

BOX

GEAR

MOTOR

DRIVE

LOCK
WASHER

WASHER

MOTOR
BRACKET

CHAIN

DRIVE

COVER

DRIVE CHAIN

SPROCKET

NUTS

4 MOUNTING

H150_0130HCA

Summary of Contents for Kodak X-Omat 3000 RA PROCESSOR

























































































Search results

Summary of Contents for Kodak X-Omat 3000 RA PROCESSOR

Reviews:

Related manuals for Kodak X-Omat 3000 RA PROCESSOR

Brands by name

Popular brands

EASTMAN Kodak X-Omat 3000 RA PROCESSOR, Adjustments

Search results

Summary of Contents for Kodak X-Omat 3000 RA PROCESSOR

Reviews:

Related manuals for Kodak X-Omat 3000 RA PROCESSOR

Brands by name

Popular brands