25
24
EASTOAK.COM
30” DIGITAL ELECTRIC SMOKER PRO
OWNER’S MANUAL
Recommendation
ERROR CODES
Error codes
Issue
Err1
Err2
Err3
Err4
Remote control
is unresponsive
Er°F orEr°C
Er°F orEr°C
Turn Smoker OFF and unplug from outlet, Replace
Thermostat Kit.
Turn Smoker OFF and unplug from outlet
Check or replace in this order
1. Replace Thermostat Kit.
2. Replace Control Panel Display Kit.
3. Replace Power Board Kit.
Turn Smoker OFF and unplug from outlet
Check or replace in this order
1. Replace Meat Probe.
2. Replace Meat Probe Housing.
3. Replace Control Panel Display Kit.
Turn Smoker OFF and unplug from outlet
Check or replace in this order
1. Replace Meat Probe.
2. Replace Meat Probe Housing.
Reset the Remote Control:
1. Main Control: press Meat probe button and hold for 3 seconds
until it beeps.
2. Remote Control: press Meat probe button twice on the remote.
Turn Smoker OFF and unplug from outlet
Check or replace in this order
1. Replace Thermostat Kit.
2. Replace Control Panel Display Kit.
3. Replace Power Board Kit.
Turn Smoker OFF and unplug from outlet
Check or replace in this order
1. Replace Meat Probe.
2. Replace Meat Probe Housing.
Alarm sounding with 3 beeps every 30
seconds and will only stop when the Power
Button is turned to off.
Blinking "Err1" appears when you press the
Power Buttonwhen starting your smoker.
Blinking "Err1" appears when you press the
Temp Button onyour smoker.
Blinking "Err1" appears when you press any
buttons on your smoker.
Refer to online Electrical Replacement
Manual for instructionson removal and
replacement.
Alarm sounding with 3 beeps every 30
seconds and will only stop when the Power
Button is pressed Blinking "Err2" appears
when you press the Power Button when
starting yousmoker.
Blinking "Err2" appears when you preheat
your smoker.
Blinking "Err3" appears when you press the
Meat Probe Buttoafter starting your smoker.
Blinking "Err3" appears when you press the
Meat Probe Buttonwhen you want to check
the food temperature.
after starting your smoker.Blinking "Err4"
appears when you press the Meat Probe
Buttonwhen you want to check the food
temperature.
Blinking "Err4" appears when you press the
Meat
The remote control is not sync'd to the
Smoker.
Blinking Er °F (or Er °C) appears in the
Set
Chamber Temperature
bar of your remote
control.
Blinking Er °F (or Er °C) appears in the
Meat
Probe
Tempbar of your remote control.
This device complies with Part 15 of the FCC and RSS Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept anv interference received, including interference that
may cause undesired operation.
WARNING:
• Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
• This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These imits are designed
to provide reasonable protection against harmful interterence in a residential
installation.
• This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instructions, may cause
interference harmful to radio communications.
•
There is no guarantee, however, that interference will not occur in a particular
installation. If this equipment doescause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
-
Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
-
Consult the dealer or an experienced radio or TV technician for help.
