EarthWay FLEX-SELECT Series Assembly Instructions Manual Download Page 3

Page: 3 / 10

Assembly and Operation Instructions

F80_RevNov_21

PAGE 3

Step 4:

Install

COAST WHEEL onto the AXLE

fully, then using outside Cotter Pin hole, insert
1” Cotter Pin through AXLE (not thru the wheel).
Bend with pliers to prevent pin from falling out

Step 5:

Now remove the PIVOT BRACKET

from THE LOWER HANDLES. Keep the 1/4 -20 x
2” bolts and locknuts for use in reinstallation

Step 6:

Install HANDLE SHAFT INTO LOWER

HANDLES and then reattach the PIVOT BRACKET
assembly as shown onto the LOWER HANDLES
using two 1/4 -20 x 2” bolts and locknuts.

TIGHTEN BOLTS AND NUTS NOW.

Step 7:

Remove

one 1/4-20 Hex Nut from

the CONTROL ROD. Next, push LEVER
forward to setting “0” to help align the
CONTROL ROD with hole in PIVOT BRACKET,
pull LEVER backward to insert CONTROL
ROD through hole in PIVOT BRACKET. Now
install 1/4-20 regular nut on to CONTROL
ROD.

Control Rod

Tabbed Hole

Control Rod

Lever

Tension Nut

Gauge & Lever

Summary of Contents for FLEX-SELECT Series











Search results

Summary of Contents for FLEX-SELECT Series

Reviews:

Related manuals for FLEX-SELECT Series

Brands by name

Popular brands

EarthWay FLEX-SELECT Series, Assembly Instructions Manual

Search results

Summary of Contents for FLEX-SELECT Series

Reviews:

Related manuals for FLEX-SELECT Series

Brands by name

Popular brands