background image

Check for parts online at 

www.getearthquake.com

 or call 800-345-6007 M-F 8-5

20

Operator's Manual

CS3814, CS3816, CS4116 Chainsaws

trouBleshooting and repair 

trouBleshooting guide

While normal care and routine maintenance will extend the life 

of your chainsaw, prolonged or constant use may eventually 

require that service be performed to allow it to continue oper-

ating properly. The troubleshooting guide below lists the most 

common problems, causes and remedies.

 Warning

 

practice safety at all times. engine must Be 

turned off and alloWed to cool, and spark 

plug Wire must Be disconnected and secured 

Before attempting any maintenance or repair.
failure to comply With this safety reQuirement 

can result in serious personal injury to you 

or Bystanders.

proBlem

cause

remedy

Starting failure

•   Check fuel for water or  

substandard mixture

• Replace with proper fuel

• Remove and dry the spark plug

• Pull the starter again with no choke

• Replace spark plug with a new plug

Lack of power / Poor ac-

celeration / Rough idling

• Check for water or 

  substandard mixture

• Check air filter and fuel

  filter for clogging

• Check carburetor for 

  inadequate adjustment

• Replace with proper fuel

• Clean

• Have an authorized service center adjust the 

carburetor.

Oil does not come out

• Check oil for substandard 

   quality

 •Check oil passage and

  ports for clogging

• Replace

• Clean

If the unit seems to need further service, please consult with an authorized service shop in your area.

Summary of Contents for CS3814

























Reviews: