background image

 

ACM-410D-IM (11/12) 

 

Page 2 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Disclaimer 

The EarthLinked

®

 Auxiliary Cooling Module is sold as a system component part and must be 

properly sized and matched to the system compressor unit to provide the intended performance 
and safe operation of the system.  This component must be installed by a trained technician who 
has successfully completed the ETI training class and passed the final examination. Installation 
must be made in accordance with the instructions set forth within this manual. 

Failure to provide installation by an authorized, trained installer in a manner consistent with this 
manual will void the limited warranty coverage for the EarthLinked

® 

system.

 

Earthlinked

 

Technologies shall not be liable for any defect, unsatisfactory performance, damage or 

loss, whether direct or consequential, relative to the design, manufacture, construction, application 
or installation of other components in the EarthLinked

® 

system. 

 

 
 
 
 
 
 
 
 
 

Earthlinked Technologies, Inc. 

4151 South Pipkin Road 

Lakeland, Florida 33811 

tel. 863-701-

0096 ● fax 863-701-7796 

info@earthlinked

.com ● 

www.earthlinked.com

 

Summary of Contents for ACM-024C













Reviews: