Eagle Power II Installation Manual Download Page 2 | Manualshive

Page: 2 / 19

background image

Table of Contents

UL Listings
Installing the Warning Sign / Precautions
Methods of Installation / Compact Installation
Mounting the Secondary Entrapment / Welding Gate Arn
Mounting Operator(s) to Concrete Pad(s)
Selecting the Opening Direction of Gate
Connecting the Power /

Reverse / Exit Loop Installations

Two Way Adjustable Reverse Sensors / ERD
The Feature Selector
Conencting Accessories
Master & Slave Operations
Output Connections
Description of Inputs
Receiver Connections
Gate Travel Distance / Setting the Limit Switches
Emergency Release
Resetting the Motor
Adjusting the Operator's Clutch
Troubleshooting

Page 3
Page 5
Page 6
Page 7
Page 8
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13
Page 15
Page 16
Page 17
Page 17
Page 18
Page 18
Page 18
Page 19

(2)

Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com

All rights reserved. No part of this manual may be reproduced in any
means: graphics, electronics, or mechanical, including photocopying
without the expressed written permission of the publisher. Materials,
components and specifications are subject to change without notice.

© 2006 Eagle Access Control Systems, Inc.

«
1
2
3
4
...
»

Summary of Contents for Power II




















Reviews:

No comments

Related manuals for Power II

Brand: La Marche Pages: 8

Brand: Parkside Pages: 140

Brand: Parkside Pages: 182

Brand: Parkside Pages: 98

Brand: atonos Pages: 15

Brand: Hama Pages: 36

Brand: TQ-Systems Pages: 10

Brand: T&D Pages: 2

Brand: DSR Pages: 12

Brand: Maha Energy Pages: 2

3DR Solo Pro PRCS

Brand: P-Squared Pages: 2

TruSine 4500 TSC24-4500

Brand: Vanner Pages: 30

Brand: Icom Pages: 2

Brand: Aegis Pages: 2

Brand: EASTMAN Pages: 22

Brand: Ripmax Pages: 20

Brand: Luxa 2 Pages: 11

Brand: NOCO Genius Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands