Eagle CUDA 250 S/Map Installation And Operation Instructions Manual Download

Page: 126 / 172

118

Delete icons menu.

The Delete All Icons command will ask if you are sure. Press

←

ENT

. All icons will be deleted from the map.

The Delete by Symbol command will launch the Select Symbol menu.
Use

←

↑

→

↓

to select an icon to delete, then press

ENT

. A mes-

sage will appear letting you know all icons with the selected symbol
have been deleted.

The Delete From Map command will prompt you to move the cursor
over an icon to select it. After selecting the icon, press

ENT

and it will

disappear from the map.

Navigate to an Icon

Use the Navigate to Cursor command and the cursor to select the de-
sired icon on the map.

1. Center cursor crosshairs over the icon.

2. To navigate to the selected icon location press

MENU

ENT

EXIT

. Fol-

low course line on the Map Page or the compass bearing arrow on the
Navigation Page.

Summary of Contents for CUDA 250 S/Map












































































































































































Search results

Summary of Contents for CUDA 250 S/Map

Reviews:

Related manuals for CUDA 250 S/Map

Brands by name

Popular brands

Eagle CUDA 250 S/Map, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 250 S/Map

Reviews:

Related manuals for CUDA 250 S/Map

Brands by name

Popular brands