Eagle CUDA 250 S/Map Installation And Operation Instructions Manual Download | Manualshive

Page: 106 / 172

background image

98

more than 60,000 navigation aids and 10,000 wrecks and obstructions
in U.S. coastal and Great Lakes waters

NOTE:

If you have a Cuda 250i, your unit has medium-detail maps of the
entire world.

The Map Page has its own menu, which is used for several functions
and for setting various options. To access the Map Page Menu, from the
Map Page, press

MENU

.

The Pages Menu has several display options under the Map Page cate-
gory. Press

PAGES

|

←

→

to

M

AP

|

↓

to page display option|

EXIT

.

Map with Sonar Page

This page mode splits the screen in half, with a map on the left and the
sonar chart on the right. This screen option can be found on the Pages
Menu under the Map Page category.

Map with Sonar page (left). Resize Window command selected from

sonar menu (center). Resizing the window (right).

When this screen is activated, you need to specify which side of the Menu is
active. To toggle between the two windows, press

PAGES

|

PAGES

. To switch

back, press

PAGES

|

PAGES

again.

The following page contains a 12-step quick reference for the most basic
GPS operations.

«
...
104
105
106
107
108
...
»

Summary of Contents for CUDA 250 S/Map













































































































































































Reviews:

No comments

Related manuals for CUDA 250 S/Map

Brand: CalAmp Pages: 55

Brand: Cal Amp Pages: 10

Brand: Kanardia Pages: 80

Brand: SecuLife Pages: 24

Brand: Westcoast GPS Pages: 14

COMPACTFLASH GPS

Brand: Mobile Crossing Pages: 14

OpenTracker USB

Brand: Argent Data Systems Pages: 43

Brand: XAiOX Pages: 13

Brand: NorthStar Pages: 232

Brand: S-TEC Pages: 34

Brand: Enfora Pages: 54

StarFinder Aire

Brand: Laipac Pages: 41

PANASONIC GYRO RDR-3200

Brand: RoyalTek Pages: 25

Brand: RoyalTek Pages: 27

Brand: RoyalTek Pages: 48

Brand: Parrot Pages: 21

Brand: TomTom Pages: 13

Brand: Haicom Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands