Eagle CUDA 250 S/Map Installation And Operation Instructions Manual Download | Manualshive

Page: 118 / 172

background image

110

New trail, named Trail 3, is created when Trail 2 is made inactive. Any

new travel will be recorded in this trail, which is active and visible.

Trails do not need to be visible in order to be active.

You can save and recall up to 10 different plot trails.

Tip:

Another quick way to stop recording one trail and begin a new one
is to use the New Trail command. Press

MENU

|

MENU

|

↓

to

M

Y

T

RAILS

|

ENT

. Use

→

to select

N

EW

T

RAIL

and press

ENT

.

Caution:

You also have the option of completely turning off trail record-
ing, under the trail Options command. If, however, the Update
Active Trail option is left turned off, it will cancel the automatic
trail creation feature.

Displaying a Saved Trail

The active trail is automatically displayed on the with the default set-
tings. You can selectively turn trail display on and off for any saved or
active trail. In the Saved Trails List, visible trails have a check mark in
front of the trail name.

«
...
116
117
118
119
120
...
»

Summary of Contents for CUDA 250 S/Map













































































































































































Reviews:

No comments

Related manuals for CUDA 250 S/Map

Brand: Novatel Pages: 2

Triton Triton 300

Brand: Magellan Pages: 56

iQue M3 - Win Mobile

Brand: Garmin Pages: 20

Brand: Leica Pages: 6

Brand: Teltonika Pages: 18

Brand: BlueCats Pages: 7

Apollo SL50 GPS

Brand: II Morrow Inc. Pages: 62

Brand: Tektronix Pages: 482

Brand: CHC Pages: 8

Brand: Garmin Pages: 67

Intelliroute TND-510

Brand: Rand McNally Pages: 148

Brand: UniGuard Pages: 14

Brand: SkyCaddie Pages: 32

Brand: SkyCaddie Pages: 38

Brand: SkyCaddie Pages: 42

Brand: SkyCaddie Pages: 49

NavAtlas XNAV9525

Brand: Dual Pages: 36

Brand: Eelink Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands