3
E-flite PT-19 ARF Assembly Manual
Recommended Radio Equipment,
Radio Controlled Version
You will need a minimum of a 4-channel transmitter,
receiver and four servos. You can choose to purchase
a complete radio system. If you are using an
existing transmitter, just purchase the other required
equipment separately. We recommend the crystal-
free, interference-free Spektrum
™
DX5e 2.4GHz DSM
®
5-channel system. If using your own transmitter, we
recommend the E-flite S75 Sub-Micro servos.
If you own a Spektrum radio, just add a DSM2
™
receiver and four E-flite S75 Sub-Micro servos. We
show the installation of the AR6100 receiver in the
manual.
Radio System
SPM5500
DX5e DSM2 5CH system
Or Purchase Separately
any of the Following Receivers
SPMAR500
AR500 DSM2 5-Channel Full-
Range Receiver (for DX5e, DX6i
or DX7)
SPMAR6100
AR6100 DSM2 6-Channel Park
Flyer Receiver (for DX5e, DX6i,
or DX7)
SPMAR6100E
AR6100E DSM2 6-Channel Park
Flyer Receiver (for DX5e, DX6i,
or DX7)
SPMAR6200
AR6200 DSM2 6-Channel Full
Range Receiver (for DX5e, DX6i,
or DX7)
And
EFLRS75
7.5-gram Sub-Micro
Servo (4)
EFLREX6L
6-inch Extension, Lightweight (2)
EFLRYH3
3-inch Y-harness, Lightweight
Recommended Equipment,
Control Line Version
EFLA170
Control Line Handle
EFLA171
52’ Braided Steel Lines
EFLA172
Control Line Motor Timer
SIGSH561
Sig Mfg Lead Balancing
Weight (1/4 ounce)
Optional Accessories
EFLA110
Power Meter
EFLC3005
Celectra
™
1- to 3-Cell
Li-Po Charger
EFLC505
Intelligent 1- to 5-Cell
Balancing Charger
EFLA150
Military Pilot (1 or 2)
Brushless Outrunner Setup
EFLM1400
Park 450 Brushless Outrunner
Motor, 890Kv
APC10070E
10x7 Electric Propeller
EFLP1080E
10X8 Electric Propeller
EFLA1030
30-Amp Pro Switch-Mode
BEC Brushless ESC
or
EFLM1505
Park 480 Brushless Outrunner
Motor, 1020Kv
APC12060E
12x6 Electric Propeller
EFLA1040L
40-Amp Lite Pro Switch-Mode
BEC Brushless
and
EFLA172
Motor Timer (control line only)
EFLB21003S
2100mAh 3S 11.1V 20C Li-Po,
13AWG EC3
Required Tools and Adhesives
Tools & Equipment
Card stock
Epoxy brushes
Low-tack tape
Medium grit sandpaper
Mixing cups
Mixing sticks
Paper towels
Pencil
Pin drill
Pliers
Rubbing alcohol
Ruler
Scissors
Square
String/dental floss T-pins
Trim seal tool
Phillips screwdriver: #0, #1
Felt-tipped pen
Rubber bands (optional)
Heat gun
Sealing iron
Hobby knife (#11 blade)
Nut driver: 1/4-inch, 5.5mm
Hex wrench or ball driver: 1.5mm, 3/32-inch
Drill bit: 1/16-inch (1.5mm), 1/8-inch (3mm)
Adhesives
Threadlock
30-Minute Epoxy (HAN8002)
Thin CA
6-Minute Epoxy (HAN8000)
Note on Lithium Polymer Batteries
Lithium Polymer batteries are significantly
more volatile than alkaline or Ni-Cd/
Ni-MH batteries used in RC applications.
All manufacturer’s instructions and warnings
must be followed closely. Mishandling of
Li-Po batteries can result in fire. Always
follow the manufacturer’s instructions when
disposing of Lithium Polymer batteries.
The Spektrum trademark is used with permission
of Bachmann Industries, Inc.
