ALIGNMENT PROCEDURE
6-4
selected. These parameters default to the last selected
condition the next time the program is started.
Read Tune Parameters -
Selecting this function or
clicking the
button reads the tune parameters
currently programmed in the transceiver and displays
them in the various screens.
NOTE: Values in the various screens are for reference
only and adjustments should be done only by using the
Partial Tune function.
Write Tune Parameters -
Selecting this function or
clicking the
button writes the current tune param-
eters to the radio. This occurs automatically when a
Partial Tune adjustment is completed.
Tune Complete -
Currently not available. This func-
tion automatically steps through all the tests required
to tune the radio.
Tune Partial -
Selecting this function or clicking the
button selects the Partial Tune mode. This mode
automatically steps through all the adjustments of the
currently selected Tune Category.
6.3.4 TOOLS MENU
Reset Radio -
Resets the radio control logic similar to
cycling power. This can be used, for example, to
change the radio series or band or exit an adjustment
before it is complete.
Set Band -
Selects the operating band of the radio. All
tuning values are reset to the factory defaults.
CAUTION:
Do not select this function because it can
make the radio non-functional.
Reset Passwords -
Erases all password information
contained in the radio. This function can be used, for
example, to allow reprogramming of passwords if they
are lost.
NOTE: Radio personality information is not
erased by this function.
Erase EEPROM
CAUTION:
This function erases important radio
programming information as described below.
Complete
-
Erases all EEPROM information,
including factory programmed parameters.
CAUTION:
Do not select this function because the
radio must be returned to the factory to make it
operational again.
Parms Only - Erases all personality information.
NOTE: The radio must be reprogrammed after this
function is selected.
Tx/Rx Tests -
Selects a screen which is used to check
digital (P25) receive and transmit performance. Refer
to Section 6.5 for more information.
Restore Rx Front End Parameters -
Programs the
radio with default receive front end tune parameters.
Other parameters remain unchanged.
6.3.5 HELP MENU
Displays the version number of the PCTune
software and other information.
6.4 TUNING PROCEDURE
6.4.1 CONNECTING TEST SETUP
1. With transceiver power turned off, connect the –940
test cable to an unused serial port of the computer
(see Section 6.1). The –920 programming cable (see
Summary of Contents for 5100 Series
