background image

E+E Elektronik Ges.m.b.H. accept warranty and liability claims neither upon this publication nor in case of improper 

treatment of the described products.
The document may contain technical inaccuracies and typographical errors. The content will be revised and  

updated on aregular basis. The described products can be improved and changed at any time without prior notice.

© Copyright E+E Elektronik Ges.m.b.H. 

All rights reserved.

EMC note USA (FCC):

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when 

the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio 

frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful 

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful 

interference in which case the user will be required to correct the interference at his own expense.

EMC note Canada (ICES-003):

CAN ICES-3 (A) / NMB-3 (A)

Summary of Contents for EE610

















Reviews: