23
C
ONFIGURA
TION
6.
6.
6.
6.
6.
C
C
C
C
C
ONFIGURA
ONFIGURA
ONFIGURA
ONFIGURA
ONFIGURATION
TION
TION
TION
TION
6.1
Initializing DeviceNet Communications ................................................................................. 23
6.2
Setting the Node Address and Baud Rate ............................................................................. 23
6.3
Electronic Data Sheet File (EDS) ........................................................................................... 23
6.4
Parameter Configuration ..................................................................................................... 24
6.1
6.1
6.1
6.1
6.1
IIIII
NITIALIZING
NITIALIZING
NITIALIZING
NITIALIZING
NITIALIZING
D
D
D
D
D
EVIC
EVIC
EVIC
EVIC
EVICE
E
E
E
E
N
N
N
N
N
ET
ET
ET
ET
ET
C
C
C
C
C
OMMUNICA
OMMUNICA
OMMUNICA
OMMUNICA
OMMUNICATIONS
TIONS
TIONS
TIONS
TIONS
When the transmitter is connected to the DeviceNet bus, it will perform an initialization sequence to
establish communications with the Master.
1.
Initially, the Device Status LED will flash red one time, and then will change to a steady green.
At this point the Transmitter has passed its internal health check.
2.
Simultaneously, the Network Status LED will flash green one time, then after a few seconds
will continue to flash green.
3.
At this point, the duplicate MAC ID check is complete, and the transmitter is waiting to be
allocated to a Master.
4.
If the Network status LED stays solid red, remove the connector and then reconnect. If the
LED is still solid red, continue to section 6.2 Setting the Node Address and Baud Rate
6.2
6.2
6.2
6.2
6.2
S
S
S
S
S
ET
ET
ET
ET
ETTING
TING
TING
TING
TING
THE
THE
THE
THE
THE
N
N
N
N
N
ODE
ODE
ODE
ODE
ODE
A
A
A
A
A
DDRE
DDRE
DDRE
DDRE
DDRES
S
S
S
SS
S
S
S
S
AND
AND
AND
AND
AND
B
B
B
B
B
A
A
A
A
AUD
UD
UD
UD
UD
R
R
R
R
R
A
A
A
A
ATE
TE
TE
TE
TE
The Node Address and Baud Rate are set via explicit messaging by means of any commercially-available
DeviceNet configuration tool.
1.
The default node address is 63,
63,
63,
63,
63, and the default baud rate is 125K
125K
125K
125K
125K.
2.
If the node address is changed, the DeviceNet Pressure Transmitter will reinitialize prior to assuming
the new node address.
3.
If the baud rate is changed, it is necessary to disconnect the transmitter from the network. The
transmitter will assume the new baud rate once it is reconnected to the network and it has
reinitialized.
6
6
6
6
6.....3
3
3
3
3
E
E
E
E
E
LE
LE
LE
LE
LECTRONIC
CTRONIC
CTRONIC
CTRONIC
CTRONIC
D
D
D
D
D
A
A
A
A
AT
TT
TTA
A
A
A
A
S
S
S
S
S
HEET
HEET
HEET
HEET
HEET
F
F
F
F
F
ILE
ILE
ILE
ILE
ILE
(ED
(ED
(ED
(ED
(EDS)
S)
S)
S)
S)
The EDS or Electronic Data Sheet file for the Dynisco DeviceNet Pressure Transducer is named PT46XDN.EDS
and is available online at
www.dynisco.com
. The EDS file is used to automate the DeviceNet network
configuration process by precisely defining vendor-specific and required device parameter information.
Summary of Contents for PT460DN
Page 38: ...38 CE DECLARATION...
