manualshive.com logo in svg

Dynatronix Diamond 10kW Series, Operating Manual, Page: 4 / 150

Share
Download
Dynatronix Diamond 10kW Series Operating Manual Download Page 4

Page 4 of 150 

 

198-1603-03 Rev 01 

A.5

 

D

ISPLAY 

S

ELECT 

M

ENU

 ......................................................................................................................................................... 85

 

A.6

 

U

NIT 

S

ETUP 

M

ENU

 ................................................................................................................................................................ 86

 

A.6.1 Cycle Setup Menu .......................................................................................................................................................... 87

 

A.6.2 Output Setup Menu ........................................................................................................................................................ 88

 

A.6.3 Reading Setup Menu ...................................................................................................................................................... 89

 

A.6.4 Ramp Setup Menu .......................................................................................................................................................... 90

 

A.6.5 Tolerance Setup Menu ................................................................................................................................................... 91

 

A.6.6 Error Handling Setup Menu .......................................................................................................................................... 92

 

A.7

 

U

NIT 

C

ONFIGURATION 

M

ENU

 ................................................................................................................................................ 93

 

A.7.1 Totalizer Configuration Menu ....................................................................................................................................... 94

 

A.7.2 Host Port Configuration Menu ...................................................................................................................................... 95

 

A.7.3 Remote Control Configuration Menu ............................................................................................................................ 96

 

A.7.4 System Configuration Menu .......................................................................................................................................... 97

 

A.7.5 Calibrate Configuration Menu .................................................................................................................................... 104

 

APPENDIX B: HOST PORT PROTOCOL .............................................................................................................................. 110

 

B.1.1 Host Protocol Version Information ............................................................................................................................. 110

 

B.1.2 Command List.............................................................................................................................................................. 110

 

B.1.3 Command Format ........................................................................................................................................................ 112

 

B.1.4 Formatting Rules ......................................................................................................................................................... 112

 

B.1.5 Unit Addressing (@AA.a) ............................................................................................................................................ 114

 

B.1.6 Communications Settings (factory default) – RS485 ................................................................................................... 114

 

B.1.7 CRC Calculation ......................................................................................................................................................... 115

 

B.1.8 ACK Response Command ............................................................................................................................................ 116

 

B.1.9 NAK Response Command ............................................................................................................................................ 117

 

B.1.10 CRC Disable/Enable Command “c” ......................................................................................................................... 119

 

B.1.11 Delimiter Text Disable/Enable Command “i” .......................................................................................................... 120

 

B.1.12 Setup Command “s”: ................................................................................................................................................ 121

 

B.1.13 Waveform Command “w”: ........................................................................................................................................ 124

 

B.1.14 State Command “a”: ................................................................................................................................................. 127

 

B.1.15 Readings Command “d”: .......................................................................................................................................... 128

 

B.1.16 Module Status Command “ms”:................................................................................................................................ 130

 

B.1.17 Error Status Command “m”: .................................................................................................................................... 132

 

B.1.18 Error History Command “h”: ................................................................................................................................... 134

 

B.1.19 Unit Settings Command “t”: ..................................................................................................................................... 135

 

B.1.20 Channel Config Command “n”:................................................................................................................................ 138

 

B.1.21 Unit Info Command “u”: .......................................................................................................................................... 139

 

APPENDIX C: ERROR CODES ................................................................................................................................................ 141

 

REVISION HISTORY ................................................................................................................................................................. 150

 

 

Summary of Contents for Diamond 10kW Series























































































































































Reviews:

No comments