Dynatron 150plus Service Manual Download Page 38 | Manualshive

Page: 38 / 65

background image

Dynatron

®

150

plus

Technical Specifications

32

Definition of Symbols

Some or all of the following symbols are included in the labeling for this device. The
meanings of the symbols are described here.

!

Alternating Current

Attention, consult accompanying documents

Off (power: disconnection from the mains)

On (power: connection to the mains)

Type BF (patient-applied part)

Equipment Classification

This device is classified as follows:

•  According to the type of protection against electric shock: Class I

•  According to the type of protection against electric shock: Type BF

•  According to the degree of protection against harmful ingress of water: ordinary

•  According to the degree of safety of application in the presence of a flammable

anesthetic mixture with air or with oxygen or nitrous oxide: Equipment not
suitable for use in the presence of a flammable anesthetic mixture with air or with
oxygen or nitrous oxide.

• According to the mode of operation: Continuous operation

Disposal of Equipment and Accessories

There is no risk posed in disposal of this equipment or its accessories. These items
contain no hazardous materials.

«
...
36
37
38
39
40
...
»

Summary of Contents for 150plus


































































Reviews:

No comments

Related manuals for 150plus

WJHD309A - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 79

Brand: Raymarine Pages: 90

Brand: 1010music Pages: 2

Brand: 1010music Pages: 4

Brand: JB-Lighting Pages: 60

Brand: Facnor Pages: 33

Brand: Garelick Pages: 2

Brand: Gardico Pages: 2

Brand: OceanSat Pages: 85

Brand: Jaga Pages: 32

Brand: Landoll Pages: 70

Brand: Landice Pages: 19

Brand: Landice Pages: 7

Brand: MacDon Pages: 2

ST60+ SPEED INSTRUMENT

Brand: Raymarine Pages: 60

Brand: Raymarine Pages: 15

Brand: Raven Pages: 58

Brand: Raven Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands