Dynatron 150plus Service Manual Download Page 19 | Manualshive

Page: 19 / 65

background image

Dynatron

®

150

plus

Treatment Instructions

13

Display Watts or Watts/cm

2

Power for the Dynatron
150plus may be displayed as
WATTS or WATTS/cm

2

. The

default setting for power is
WATTS/cm

2

, but you may

select the display you prefer at
any time before or during a
treatment.

• To change the power display,

press both the POWER UP
and DOWN arrow keys at the
same time. To change back,
just press both keys again,
simultaneously.

• The power display setting you choose remains in effect until you change it again.

• You can tell when you have selected WATTS or WATTS/cm

2

by the decimal in

the POWER DISPLAY window.

- A steadily-lighted decimal means the power is displayed in WATTS/cm

2

.

- A blinking decimal means the power is displayed in WATTS.

Restore Factory Defaults

The Dynatron 150plus has the following default settings:

•  Soundhead Warming: ON
•  Coupling Sensing: OFF
•  Power Display: Watts/cm

2

Each of these settings may be changed by the user (instructions are provided earlier
in this section). If you have changed the settings for this device, but would like to
return ALL the default settings to those that were set at the factory, do the following:

1. Turn the machine OFF.

2.

Press and hold the START key while turning the machine on. The machine will
display “56” in the TIME DISPLAY window and “FP” in the POWER DISPLAY
window followed by a single beep indicating that the parameters have been reset.

Press both the UP and DOWN
arrow keys at the same time to
change the display.

POWER

PAUSE

STOP

START

A non-blinking decimal = Power displayed in Watt/cm

2

A blinking decimal = Power displayed in Watts

Dynatron 150plus Power Display. You can view
power in either WATTS/cm

2

or Watts.

«
...
17
18
19
20
21
...
»

Summary of Contents for 150plus


































































Reviews:

No comments

Related manuals for 150plus

Brand: Baker Instrument Company Pages: 24

Brand: NEC Pages: 29

Brand: ACE INSTRUMENTS Pages: 15

Brand: Wave Fitness Pages: 15

Brand: B. Braun Pages: 2

Aesculap Neurosurgery

Brand: B. Braun Pages: 13

Aesculap AdTec mini

Brand: B. Braun Pages: 2

Brand: B.Well Pages: 2

Brand: B. Braun Pages: 55

BA Ultimate LED

Brand: B.A. International Pages: 234

Brand: Califone Pages: 7

Brand: CALITEK Pages: 16

Brand: LAHTI PRO Pages: 20

Brand: LAHTI PRO Pages: 16

Brand: J&M Pages: 53

Brand: Qazqa Pages: 2

Brand: Ecler Pages: 108

Brand: R&S Pages: 121

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands