manualshive.com logo in svg

Dynamix US-SE, User Manual, Page: 60 / 105

Share
Download
Dynamix US-SE User Manual Download Page 60

Dynamix UM-SE G.SHDSL.bis EFM Bridge Modem User Manual    V003

                                                          59 

 

 

3.8.2 Config 

Tool 

 

This configuration tool has three functions: load Factory Default, Restore Configuration, and 

Backup Configuration. 

Press CONFIG TOOL, you can view the following: 

 

 

 

Choose the function and then press Finish. 

 

Load Factory Default: It will load the factory default parameters to the EFM modem.   

Note: This action will change all of the settings to factory default. On the other hand, you 

will lose all the existing configured parameters.   

 

Restore Configuration:   

In case of the configuration crushed occasionally, it will help you to recover the backup 

configuration easily. 

Click Finish after selecting Restore Configuration. 

Browse the route of backup file then press finish. The EFM modem will automatically restore 

the saved configuration. 

 

Backup Configuration:   

After configuration, suggest using the function to backup your EFM modem parameters in the 

PC. Select the Backup Configuration and then press Finish. Browse the place of backup file 

named backup. Press Finish. The EFM modem will automatically backup the configuration. 

   

Summary of Contents for US-SE










































































































Reviews:

No comments