Dynamic Engineering PMC-XM-DIFF User Manual Download | Manualshive

Page: 20 / 46

background image

Embedded Solutions

Page 20 of 46

XM_CHAN0/1_TX_AMT_LVL

[0x0024, 0x0054] TX Almost Empty Level Register (read/write)

TX Almost Empty Level Register

Data Bit

Description

31-16

Spare

15-0

TX FIFO Almost Empty Level

FIGURE 10 PMC-XM SPARTAN3 CHANNEL TX ALMOST EMPTY REGISTER

This register specifies the level at which the transmit FIFO almost empty level will be
asserted. When the number of data words in the transmit FIFO is less than or equal to
this count the almost empty status will be asserted.

XM_CHAN0/1_RX_AFL_LVL

[0x0028, 0x0058] RX Almost Full Level Register (read/write)

RX Almost Full Level Register

Data Bit

Description

31-16

Spare

15-0

RX FIFO Almost Full Level

FIGURE 11

PMC-XM SPARTAN3 CHANNEL RX ALMOST FULL REGISTER

This register specifies the level at which the receive FIFO almost full level will be
asserted. When the number of data words in the receive FIFO is greater than or equal
to this count the almost full status will be asserted.

«
...
18
19
20
21
22
...
»

Summary of Contents for PMC-XM-DIFF















































Reviews:

No comments

Related manuals for PMC-XM-DIFF

Brand: Keithley Pages: 149

Brand: Yamaha Pages: 50

Brand: A&D Pages: 30

Brand: JB Systems Pages: 12

Brand: Jackco Pages: 6

Brand: Mackie Pages: 18

Brand: Mackie Pages: 2

Brand: Mackie Pages: 8

Brand: Mackie Pages: 7

Brand: Raymarine Pages: 3

SmartPilot ST8002

Brand: Raymarine Pages: 48

Brand: Raymarine Pages: 38

hsb2 PLUS Series

Brand: Raymarine Pages: 248

Brand: Wassermann Pages: 24

Brand: Leica Pages: 36

Brand: impact Pages: 12

Brand: Otto Bock Pages: 20

Brand: Kärcher Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands