Dynamax HPFM3 Installation And Operation Manual Download Page 28

Page: 28 / 86

Photo 1

Air Regulator Pressure

Revision: JUNE 2017

WARNING!

Do not pressure the compressed air supply hose to above 690 kPa (100 PSI)

while the hose is disconnected! Do not disconnect or connect the hose if

the pressure is above 70 kPa(10PSI)!

5.3.1 Tips for Setting the Pressure Regulator

The valve at the top of the bottle should not be opened until the regulator pressure set

screw is backed off

completely. Once this is done, open the valve on the bottle completely. Check the bottle pressure gage. The pressure

should be at least 4.15 Mpa (600 PSI). This pressure is required when running a transient state flow. The minimum

pressure forces enough compressed gas to the captive air tank (CAT) to keep a steady, linear pressure increase

during the test. Close the tank valve, and release the hose pressure by pressing on the valve release needle.

WARNING!

Do not pressure the compressed air supply hose to above 690 kPa

(100 PSI) while the hose is disconnected! Do not disconnect or connect the

hose if the pressure is above 70 kPa (10 PSI)!

The “disconnects” on the air pressure hose and HPFM system has a working pressure of 690 kPa (100 PSI). Pressure on

the disconnect seals above 690 kPa (100 PSI) could cause a catastrophic failure of the “disconnect system” or personal

injury. You also can generate a loud, annoying “pop” sound unless the pressure is released first.

Increase the air regulator pressure to 138 kPa (20 PSI) and check for leaks again. Decrease the pressure by backing off

the regulator screw. Depress the end of the “disconnect” into a hard flat surface such as a coin. This will open the

disconnect seal and release the small amount of gas in the hose.

Summary of Contents for HPFM3























































































Search results

Summary of Contents for HPFM3

Reviews:

Dynamax HPFM3, Installation And Operation Manual, Page: 28 / 86

Search results

Summary of Contents for HPFM3

Reviews: