Dynamax Dynamet 5 User Manual Download | Manualshive

Page: 68 / 83

background image

Dynamet 5

67

7.3 Short-haul Modem (SHM)

The Short-haul modem is a compact interface device that can be
used  to  transmit  and  receive  serial  data  over  relatively  long
distances  that  are  not  achievable  using  RS232  interface.  The
modem unit plugs directly in to the COM port on an asynchronous
device.

SHM is a non-powered line driver with a 1500VAC lightning surge
protection  and  noise  rejection.  The  unit  shown  in  the  figure  is
switch selectable and operates using 4 wires on screw terminals
or  RJ11  connector.  For  using  with  Dynamet  5  modem  is
connected in point-point 4-wire Full-duplex mode where only software handshake is applicable.

SHM Non-Powered RS-232 Line Driver
Communication modes

Full duplex/simplex switch selectable
Loop back

Features

No External Power Required
DCE/DTE Switch Selectable
Long Distance Transfer Via Economical TP Cable
Compact Size

7.3.1 Specifications

Function

Specification

Connectors

RS-232 DB-25 Female, RJ-11 Jack
4 Screw Terminal

Switches

SW1

DCE, DTE, Loop Back Select

SW2

Full Duplex, Simples Select

Cable Length

3.5 Km (Max.) @ 4800 bps

2 Km (Max.) @ 9600 bps

800 m (Max.) @ 19200 bps

Interface

RS-232

Data Transfer Speed

110 ~ 38400 bps

Power Consumption

No external Power source Required

Housing

Plastic

Weight

60 g

Dimensions (L x W x H)

54 x 74.5 x 18.5 mm

1
2

3

4

25 pin serial
connector

RX (DCE)
TX (DTE)

Full
Duplex

TX (DCE)
RX (DTE)

Loop
Back

DTE

DCE

RJ-11

IC 150

«
...
66
67
68
69
70
...
»

Summary of Contents for Dynamet 5




















































































Reviews:

No comments

Related manuals for Dynamet 5

Brand: La Crosse Technology Pages: 32

Brand: La Crosse Technology Pages: 15

Brand: La Crosse Technology Pages: 12

Brand: La Crosse Technology Pages: 8

Brand: NASA Pages: 26

Brand: Steinberg Systems Pages: 47

Brand: Hyundai Pages: 48

Brand: Froggit Pages: 43

Brand: JBL Pages: 116

Brand: La Crosse Pages: 32

Energy Docking 300

Brand: Energy System Pages: 48

Brand: Schulte Elektrotechnik Pages: 4

Brand: La Crosse Pages: 26

Brand: Steinberg Systems Pages: 7

Brand: Icy Box Pages: 16

Brand: Dok Pages: 21

Brand: La Crosse Technology Pages: 31

Brand: Kensington Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands