manualshive.com logo in svg

Dynamax Dynamet 5, User Manual

Share
Download
Dynamax Dynamet 5 User Manual Download Page 25

Dynamax Inc 

 24 

 

3.3  Sensor Installation 

 
Dynamet 5 weather station sensors basic or additional are supplied with sensors or connected 
to the data logger in the Dynamet 5 enclosure. In this section we discuss the procedure to install 
the sensors on tripod along with  Dynamet 5 enclosure,  cable routing,  setting up/ orientation of 
the sensors and Entering parameters in the Dynamet 5 program.  

 
 
 

 

3.3.1  MaxiMet GMX500 

 

MaxiMet GMX500 is an advanced compact weather station designed and manufactured by Gill 
instruments using proven technology to measure meteorological and environmental parameters 
to international standards. 

  The MaxiMet uses the Gill WindSonic wind speed and direction sensor. The WindSonic 

measures the times taken for an ultrasonic pulse of sound to travel from the North (N) 
transducer to the South (S) transducer, and compares it with the time for a pulse to travel 
from S to N transducer. Likewise times are compared between West (W) and East (E), 
and E and W transducer. 

 

 

Summary of Contents for Dynamet 5




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands