DX Engineering DXE-OTMC-250P Instructions Manual Download Page 16 | Manualshive

Page: 16 / 20

background image

- 15 -

Manual Updates

Every effort is made to supply the latest manual revision with each product. Occasionally a manual
will be updated between the time your DX Engineering product is shipped and when you receive it.

The OMNI-

TILT

™ tilt base is capable of mounting a wide variety of vertical antennas and

masts. As new mounting schemes are tested, this manual will be revised to include the latest
information.

Please check the DX Engineering web site (

www.dxengineering.com

) for the latest revision manual.

The following drawing shows the laser cut hole pattern in the

OMNI-

TILT

™

base (front plate).

The various hole spacing can accommodate a wide variety of vertical antenna bases and clamps for
different mounting schemes.

- 15 -

«
...
14
15
16
17
18
...
»

Summary of Contents for DXE-OTMC-250P





















Reviews:

No comments

Related manuals for DXE-OTMC-250P

Brand: Tallymatics Pages: 9

Brand: NARDA Pages: 26

BAS-2333 LOGO-700

Brand: BAS Pages: 2

DXE-MBVE-1UGBRT3

Brand: DX Engineering Pages: 12

Brand: DX Antenna Pages: 3

Brand: DX Engineering Pages: 28

CMAX-O-CPUSEWV53

Brand: CommScope Pages: 3

MATV DAT75HDBOSS

Brand: Televes Pages: 2

Brand: TechniSat Pages: 84

Brand: Metronic Pages: 2

Brand: Vaisala Pages: 23

Brand: Globalstar Pages: 57

Brand: M2 Antenna Systems Pages: 6

Brand: GSS Pages: 12

Brand: GSS Pages: 12

Brand: M2 Antenna Systems Pages: 6

Brand: Emerson Pages: 134

Brand: Ebyte Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands