background image

- 7 - 

Installing the OMNI-

TILT

™ Tilt Base Ground Mounting Pipe 

 
The following is a suggested 2” OD mounting pipe installation. You may want a heavier and/or 
longer ground mounted pipe depending on your soil conditions and the type of antenna mast 
being used with the 

OMNI

-TILT™ base. Refer to your antenna’s manual for possible 

suggestions. The OMNI-TILT

 DXE-OTMC-250P Double V-Clamp fits pipes from 1.25” to 2.5” 

in diameter. 

 

Wooden Post 

 

The 

OMNI-

TILT

 Tilt Base can be installed to a customer supplied wooden post or to a ground 

mounted antenna mounting pipe.  Since there are multiple considerations in mounting to a wooded 
post, the customer will have to decide what hardware to use.  
 

Ground Mounted Pipe 

 

Use a customer supplied thick-walled galvanized steel mounting pipe 

at least

 4 feet long. This will allow approximately 2 feet or more to 

be below ground and 20 inches above ground. A thick-walled steel 
pipe 1-3/4" OD to 2" OD 

maximum

 is recommended with a minimum 

thickness of 1/8" (1/4" preferred) should be used. 

The standard 1-

1/2" galvanized water pipe (with its 1.9" OD) is just fine for this 
application and can usually be found at your local home building 
supply store.

 For permanent mounting, use a post-hole digger to 

make the hole deep enough to accommodate at least 2 feet of pipe and 
a couple inches of gravel at the bottom for drainage. Set the mounting 
pipe on the gravel, use the pre-mix concrete to fill around the pipe, 
adding water and mixing as you fill or mix the concrete first, then 
pour in the hole (depends on the type of quick concrete you 
purchase). Fill the hole until the concrete is level with the ground 
around it. Use a level on the mounting pipe as you fill the hole to be 
sure it is vertically straight. Allow to set overnight or per the concrete 
manufacturer’s recommendations. Your location, landscape and 
ground conditions may require different mounting solutions in order 
to have the steel mounting pipe and the vertical antenna in a secure 
position.  A black vinyl cap (

DXE-VC-2000 

for 2” pipe) can be used 

to cap the top of the mounting pipe to prevent water and debris from 
getting into the pipe. 

 

Note:   Galvanized steel, rather than aluminum, is much more suitable for mounting in concrete. 

Aluminum will quickly corrode due to incompatibility with the materials used to make 
concrete. 

 

 

Optional Radial Plate to Mounting Pipe

 

 

Install the optional patented 

DXE-RADP-3

 Radial Plate on the 2" OD customer supplied mounting 

pipe using the

 DXE-SSVC-2P

 V-Bolt Saddle Clamp as shown.  The standard 1-1/2" galvanized 

water pipe (with its 1.9" OD) is just fine for this application and can usually be found at your local 
home building supply store. Mount the Radial Plate so you have approximately 1" of space between 

Summary of Contents for DXE-OTMC-250P





















Reviews: