DWT ESP01-250, Original Instructions Manual

Page: 23 / 132

23
English
Work sequence (see fig. 9)
• Prepare the sprayed material and surface as de-
scribed above�
• Detach reservoir 5 , fill it with the sprayed material,
and connect it to the spray gun�
• For model ESP05-200 T , adjust the stream shape�
• Switch on the power tool, adjust the volume of the
sprayed material as described above� The "mist" of
spray deflection should be homogeneous and fine.
• Do a trial treatment on an unnecessary piece of the
same material in order to make sure that the adjust-
ments are correct�
• Spray material from a distance of 5-30 cm from the
surface (see fig. 9.1).
• For model ESP01-250 - use flexible extension
hose 17 when painting horizontal or sloping sur-
faces�
• For model ESP05-200 T - slightly tilt the spray
gun when painting horizontal or sloping surfaces�
• Start spraying beyond the bounds of the treated sur-
face�
• Move the spray gun moving your arm as shown in
figure 9.1, and not only the wrist (see fig. 9.2). The dis -
tance between the spray gun and the treated surface
should be constant - this will ensure that the material
is sprayed evenly�
• Smoothly move the spray gun as shown in
figure 9.3. Each successive strip should partially over -
lap the preceding one� Do not delay the spray gun in
one spot - this will cause drips�
• Do not interrupt spraying within the treated surface�
• Do not allow reservoir 5 to empty when working�
Tube 18 should be immersed in the liquid at all times,
otherwise the spraying process will be stopped, and
the surface will be treated unevenly�
Power tool maintenance /
preventive measures
Before carrying out any works on the power tool it
must be disconnected from the mains.
Cleaning of the power tool (see fig. 10-14)
The power tool must be cleaned after the
completion of work.
• Press button 4 so that the residues of the sprayed
material drain into reservoir 5 �
• Unscrew reservoir 5 and discharge the sprayed ma-
terial residues� Pour an appropriate solvent into reser-
voir 5 and connect it to the spray gun� Shake the spray
gun, then switch it on and spray the solvent into an
empty reservoir� Repeat several times until the spray
gun is absolutely clean� If you have been working us-
ing flexible extension hose 17 , then it should be in-
stalled at this step of the cleaning procedure�
• Wipe the power tool case with a cloth moistened
with an appropriate solvent� Prevent the solvent from
getting into the power tool�
• Disassemble the spray gun as shown in figures 10-11
and 13�
• Unscrew reservoir 5 and wipe it with a clean cloth�
• Remove tube 18 and make sure it is clean� Clean it,
if necessary�
• For model ESP01 - 250 , disassembly and clean
filter 24 with the use of a solvent and a soft brush, then
assembly and put filter 24 in place�
• Using rod 13 clean suction hole 25 , drain hole 26
and nozzle 1 (see fig. 12 and 14).
• Using a brush and solvent, clean all removed parts
and mount them back strictly following the installa-
tion sequence� Please note! Using sharp objects
for cleaning spray gun parts (except for the ports
mentioned above) is strictly prohibited.
• To protect internal parts from corrosion, drop a few
droplets of low viscosity oil into suction hole 25 and
drain hole 26 �
• Assembly operations do in reverse sequence�
Air filter replacing (see fig. 15)
[ESP05-200 T]
• Use a screwdriver to remove the cover 8 (see
fig. 15).
• Replace the air filter 27 �
• Install the cover 8 (the clamps of the cover 8 must
click shut)�
Cleaning of the power tool
An indispensable condition for a safe long-term exploi-
tation of the power tool is to keep it clean� Regularly
flush the power tool with compressed air thought the
ventilation slots 8 �
After-sales service and application service
Our after-sales service responds to your questions
concerning maintenance and repair of your product as
well as spare parts� Information about service centers,
parts diagrams and information about spare parts can
also be found under: www.dwt-pt.com �
•
Transportation
of the power tools
Categorically not to drop any mechanical impact on
the packaging during transport�
• When unloading / loading is not allowed to use any
kind of technology that works on the principle of clamp-
ing packaging�
Environmental
protection
Recycle raw materials instead of dispos-
ing as waste.
Power tool, accessories and packaging
should be sorted for environment-friendly
recycling�
The plastic components are labelled for categorized
recycling�
These instructions are printed on recycled paper man-
ufactured without chlorine�
The manufacturer reserves the possibility to introduce changes.