background image

G2030-II-C 

Mar ‘17 

 

- 27 -

Limited Warranty : G Series Screw Compressors 

 

The manufacturer warrants the product manufactured by it and sold to the original purchaser, when properly installed, operated, applied, and 
maintained in accordance with procedures and recommendations outlined in the manufacturer’s instruction manuals, to be free of defects in material 
and workmanship for a period of one (1) year from the date of installation, not to exceed eighteen (18) months from the date of manufacture, provided 
such defect is discovered and brought to the manufacturers attention within the aforesaid warranty period, conditional upon the following: 

1)  Genuine ‘DEV-3000’ Lubricant and Parts are used for the full warranty period. 
2)  The Unit is maintained in accordance with the manufacturer’s instruction manual for the Unit, with the following minimum maintenance 

requirements: 
A)  Complete Oil change every 8000 hours (not to exceed 12 months) from the date of initial start-up using ‘DEV-3000’ Lubricant. When 

operating in adverse conditions, Oil changes must be done more frequently. 

B) Oil Filter must be changed every 4000 hours (not to exceed 6 months) from the date of initial start-up using the appropriate DV Systems part. 

When operating in adverse conditions, Oil Filter changes must be done more frequently. 

C) Air Intake Filter must be changed every 2000 hours (not to exceed 6 months) from the initial date of start-up using the appropriate DV 

Systems part. When operating in adverse conditions, Air Intake Filter changes must be done more frequently. 

D) Air/Oil Separator Filter must be changed every 8000 hours (not to exceed 12 months) from the date of initial start-up using the appropriate 

DV Systems part. When operating in adverse conditions, Air/Oil Separator changes must be done more frequently. 

E) Appropriate and complete maintenance records must be kept by the End User. As well, the End User must retain copies of invoices 

indicating the timely purchase of the DV Systems Compressor Oil and maintenance/service parts. All records and invoices must be kept for 
the duration of the manufacturer’s warranty period. 

3) Disclaimer: 

A) The following items are considered normal wear items, and are warranted for a period of one (1) year from the date of installation, not to 

exceed eighteen (18) months from the date of manufacture; the Shaft Seal on the Air End Drive Shaft, the Intake Valve Assembly (and its 
components), and the Minimum Pressure Valve. 

B) All electrical components are warranted for a period of one (1) year from the date of installation, not to exceed eighteen (18) months from the 

date of manufacture.   

 
An additional four (4) year extended Air End Warranty and a four (4) year extended Three Phase Baldor Motor Warranty are available on those 

Units that: 

A) have been registered with the manufacturer within thirty (30) days from the date of purchase, this done by returning  the ‘DV Systems Rotary 

Screw Compressor Start-Up Sheet’ and 

B)  have been maintained in accordance with the manufacturer’s instruction manual as noted in ‘2’ above. 

 
The manufacturer will repair or replace any product or part determined to be defective by the manufacturer within the warranty period, provided such 
defect occurred in normal service and is not the result of misapplication, misuse, abuse, neglect, incorrect maintenance, accident, or normal wear. 
Normal maintenance items requiring routine replacement are not warranted. Please refer to the appropriate service bulletin to determine normal 
maintenance requirements. 
 
The warranty covers parts and labour for the warranty period (excluding the Three Phase Baldor Motors. Labour is not covered in the (4) year extended 
Baldor Motor Warranty.) Either repair or replacement shall be at the sole option of the manufacturer. Any service performed on the product by anyone 
other than the manufacturer must first be authorized by the manufacturer. Unauthorized service voids the warranty and any resulting charge or 
subsequent claim will not be paid. 
 
Products repaired or replaced under warranty shall be warranted for the unexpired portion of the warranty applying to the original product, based on the 
original date of invoice as outlined above. 
 
There is no other expressed warranty. Implied warranties including those of merchantability and fitness for a particular purpose are limited to one (1) 
year from the date of invoice to the extent permitted by law and any and all implied warranties are excluded. This is the exclusive remedy. Liability for 
consequential damages under any and all warranties are excluded to the extent exclusion is permitted by law. 
 
This warranty gives you specific rights, and you may also have other rights within your jurisdiction. 
 
This warranty does not cover: 

1) Merchandise that has become inoperative because of ordinary wear, misuse, neglect, accident, or improper and unauthorized repair or alteration. 
2) Electric Motors manufactured and identified as the product of another company. 
3) Compressor Units that have not been properly maintained in accordance with the recommended maintenance and lubrication change procedures 

and/or that have been subject to inordinate use through being inadequately sized or poorly installed. 

4) Compressor Units using other than the recommended lubricant. 
5) Costs occasioned by the removal, replacement, or repair of merchandise (other than by DV Systems) without previous authorization from DV 

Systems. 

6) Expenses incurred in travel or lodging beyond a 100 kilometre (60 mile) distance from the nearest DV Systems Authorized Service Centre. 
7) Expenses incurred in the return of equipment for inspection purposes to the manufacturers facility. All returns must be pre-authorized, returned 

‘Freight Prepaid’, and accompanied by a ‘Return Material Authorization (RMA) Number’ (obtainable through DV Systems). 

8) Products, parts, materials, components, or accessories manufactured by others or supplied in connection with the sale of the manufacturers 

products. 

9) Repair and transportation costs of merchandise determined not to be defective under the terms and conditions of this warranty. 
10) The cost of rental or loaner equipment while the customer’s original equipment is being assessed, repaired, or replaced. 
11) Consequential damages in the event of product failure. 

 
All decisions by DV Systems Inc. with regard to this policy shall be final. DV Systems will not be responsible for any claimed defective materials 
returned other than in accordance with this statement of policy or without our prior authorization. 

 

DV Systems Inc. (Canada)  

 

 

 

DV Systems, Ltd. (USA) 

490 Welham Road 

 

Tel:  (705) 728-5657 

128-B Talbert Road 

 

Tel: (704) 799-0046 

Barrie, Ontario, L4N 8Z4, Canada  Fax: (705) 728-4974 

Mooresville, NC, 28117, USA 

Fax: (704) 799-0355

 

 

 

Summary of Contents for G20






































Reviews: