DuroStar DUAL FUEL HYBRID ELITE DS12000EH User Manual Download Page 39

Page: 39 / 84

Turn breaker ON/ Connect

The breaker is located on the right side of the front power

panel. Flip the breaker up to allow the power to flow to the

receptacles. Connect your devices to the receptacles on the

front panel. Start with the largest loads first.

Open choke

Push the choke to the “OPEN” position as the engine warms

up.

Pull the recoil start

The recoil start is located on the left side panel next to the air

filter. Pull the recoil handle slowly until resistance is felt, then

quickly pull the recoil handle until fully extended.

CAUTION

: Release the recoil handle only after

the cord has retracted. Releasing the recoil

handle while extended may cause harm to

yourself or your

equipment.

Turn idle control OFF

The idle control is located on the top center of the main

power panel. Turn the switch “OFF” to prevent the unit from

trying to idle down before the engine is warmed up.

Summary of Contents for DUAL FUEL HYBRID ELITE DS12000EH





















































































Search results

Summary of Contents for DUAL FUEL HYBRID ELITE DS12000EH

Reviews:

Related manuals for DUAL FUEL HYBRID ELITE DS12000EH

Brands by name

Popular brands

DuroStar DUAL FUEL HYBRID ELITE DS12000EH, User Manual

Search results

Summary of Contents for DUAL FUEL HYBRID ELITE DS12000EH

Reviews:

Related manuals for DUAL FUEL HYBRID ELITE DS12000EH

Brands by name

Popular brands