Duracraft AMD-67E, User Instructions

Page: 6 / 78

5
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
Please read through all the instructions before starting to use the air-conditioner.
Keep this manual carefully.
1. Install the air-conditioner in a place which is inaccessible to children.
2. Do not use the air-conditioner out-of-doors.
3. Place the air-conditioner upright on a firm, even surface. Make sure it is
standing securely so that it cannot tip over or fall. Water can damage furniture and
floor coverings and cause an electric shock.
4. Unwind the cable completely. If the cable is not completely unwound, it can
overheat and could start a fire.
5. Do not use an extension cable or an adjustable speed controller. This could
cause overheating, fire or an electric shock.
6. Attach the air-conditioner only to a single plug with the same voltage as that
given on the type plate.
7. Always unplug the air-conditioner if it is not in use, or before it is moved or
cleaned. Do not pull at the cable to unplug the appliance.
8. Do not point the air-vent (d) directly at people, walls or objects.
9. The air-conditioner operates best at a room temperature of between 17°C and
35°C in the operating modes „COOL“ and „DRY“. Above or below this temperature
zone there can be operational disturbances in this mode.
10. Do not use the air-conditioner anywhere near inflammable gases or materials,
near an open fire, or where oil or water could splash. Make sure that the
airconditioner is
not exposed to direct sunlight. Do not use the air-conditioner in a
sauna, or near a bathtub, shower or swimming-pool.
11. Check that the air vents (l/m) (in) and (d) (out) are opened before the
airconditioner is switched on. The air-conditioner must not be located behind
curtains or other objects or obstacles which could restrict the circulation of air.
Make sure that no objects can get into the air-vents in (l/m) or out (d), as this
could lead to overheating, fire or electric shock.
12. Do not unplug the air-conditioner while it is switched on. You must first switch
the power switch (a) to OFF.
13. Wait for 3 to 5 minutes after switching the air-conditioner off, before switching
it back on.
14. Do not immerse the air-conditioner in water or any other fluid, and do not pour
water or any other fluid over the appliance or into the airvents (l/m) and (d).
15. Clean the air-conditioner regularly following the cleaning instructions in the
manual.
16. If the power cable of the air-conditioner is damaged it must be repaired by a
workshop approved by the manufacturer, as special tools are required.
17. Always transport the air-conditioner in an upright position. If this is not
possible, lay the appliance on its side and return it to its upright position as soon
as you arrive at your destination. After each transportation wait for at least 60
minutes before using the appliance.
18. Do not use this air-conditioner if it is damaged or shows any signs of damage
or is not working properly. Unplug the appliance from the power supply.
ASSEMBLY INSTRUCTIONS
Front (Fig. 1)
a) Control panel
b) Air deflector (up / down)
c) Air deflector (left / right)
d) Supply air deflector
e) Wheels
f) Handle
g) Water tank
h) Supply cord
Back (Fig. 2 + 7)
k) Exhaust air grille
l) Return air grille
m) Return air grille
n) Permanent condensate water drain
- Only use for permanent water draining
- Only pull out the water drain for this purpose – otherwise it becomes leaky.
Control Panel (fig. 4)
a) On/Off button
b) Compressor light
c) Water tank light
d) LCD-display
e) Temperature button
f) Operation mode button
g) Fan Speed button
h) Air deflector button
i) Timer button
FUNCTIONS
a) On/Off button to switch the appliance On and Off.
b) Compressor indicator
This indicator shows if the compressor is on or off. When cooling or
dehumidifying the green light illuminates.
c) Water tank indicator
If the water tank is full you will hear an alarm signal sound and the
red light illuminates. The compressor switches off automatically and
changes over to ventilation. When the water tank has been removed,
emptied and put back the appliance automatically changes back to
the original setting.
d) LCD-Display
1) Temperature indicator
2) Fan indicator
3) Cooling
4) Dehumidifying
5) Air deflector indicator
6) Timer-On/Off-indicator
7) Indicator of programmed room temperature
8) Fan speed indicator
9) Timer indicator
e) Temperature button
The desired temperature can be selected with this button. Each
press of the
-button increases the temperature by one degree C;
each press of the -button decreased the temperature by one
degree C. The temperature range is 16 and 30 degrees C.
f) Button to select operation mode: Fan – Cooling – Dehumidifying
g) Fan speed button
When cooling or for ventilation the fan speed can be selected by
pressing this button: low, medium, high.
h) Air deflector button: press this button to make air deflectors swivel
automatically.
i) Timer button
When the appliance is in operation you can program the switch off
time with this button. When the appliance is not operating you can
program the switch on time with this button. The maximum switch
off or switch on time is 24 hrs.
By pressing the -button the time will be increased by 30 minu-
tes; by pressing the -button it will decreased by 30 minutes
OPERATION
1. Location (Fig. 3)
Place the appliance on a dry, level surface. A minimum distance of 60 cm from any
wall or other objects must be always kept. Make sure that there are no obstacles
around the unit affecting the free circulation of air.
2. Supply cord
Only connect the appliance to a single phase a.c. supply of the voltage specified on
the rating plate. Local electrical regulations must be observedbe kept. Make sure
that no other appliances are connected to the same socket.
3. Cooling
The temperature range for cooling lies between 16 and 30 degrees C. Wait at least
3 minutes from a previous stop before restarting the compressor.
• Make sure that the water tank is in place.
• The exhaust air tube must be located outside (e.g. through an open window or
hole in the wall) so that the warm air can be discharged.
C°