Dunster House E9-3042DBPP-45 Installation Manual Download

Page: 20 / 26

All dimensions are approximate and subject to the limitations of the material used and the methods of manufacture

Page 20

94x F.1600
5x

J.1960

Roof installation

IMPORTANT - Ensure the cabin has been built square and level,
otherwise you may experience difficulties.

ROOF EDGE REINFORCEMENT TRIMS

Roof edge reinforcement trim (J.1960) may be required to be cut on site

Fit the roof edge reinforcement trim (J.1960) to the underside of the

roof boards. Use 35mm screws and always pre-drill the holes!

IMPORTANT - For optional extra Roof Insulation please refer to the
"Roof Insulation" section at the back of the manual.

ROOF BOARDS

Use 40mm nails to secure roof boards, leave 2mm gap between them

and start from the edge of the roof (flush with the end of the purlin).
Last roof board may be required to be cut to size.

Roof edge
reinforcement

Roof

boards

2mm gap

IMPORTANT - To fit and adjust door sashes please refer to
the "Door" section at the back of the manual.

F.1600

J.1960

J.1960 (Cut to suit)

J.1960

Summary of Contents for E9-3042DBPP-45



























Search results

Summary of Contents for E9-3042DBPP-45

Reviews:

Related manuals for E9-3042DBPP-45

Brands by name

Popular brands

Dunster House E9-3042DBPP-45, Installation Manual

Search results

Summary of Contents for E9-3042DBPP-45

Reviews:

Related manuals for E9-3042DBPP-45

Brands by name

Popular brands