Dunkirk GWB9-050IH-2 Installation Instructions Manual Download Page 1

 P/N# 240009449, Rev. A  [07/2012]

RETAIN THESE INSTRUCTIONS FOR 

FUTURE REFERENCE

These instructions must be affi xed on or 

adjacent to the boiler.

GWB9-050IH-2

GWB9-075IH-2

GWB9-100IH-2

GAS-FIRED, DIRECT VENT, 

CONDENSING, HOT WATER BOILER

INSTALLATION 

INSTRUCTIONS

PRODUCT LITERATURE

Lennox  Industries Inc.
Dallas, Texas

This boiler cannot be used with all types 
of chimneys. Read these instructions 
carefully before installing.

GAS-FIRED HOT WATER BOILERS

These low pressure gas fi red hot water boilers 
are design certifi ed by CSA (Canadian Standards 
Association) for use with natural and propane 
gases (100 MBH model is certifi ed for natural gas 
only). They are constructed and hydrostatically 
tested for a maximum working pressure of  50 
psi (pounds per square inch) in accordance 
with A.S.M.E. (American Society of Mechanical 
Engineers) Boiler and Pressure Vessel Code 
Section IV Standards for Heating Boilers.

WARNING

Improper installation, adjustment, 

alteration, service, or maintenance 

could result in death or serious injury. 

Refer to this manual for assistance. For 

additional information consult a quali

fi

 ed 

installer, service agency, or the gas 

supplier.

!

  

Summary of Contents for GWB9-050IH-2

























































Reviews: