DUDOFF GD-Z01 Installation And User Instructions Manual Download Page 9

9

INSTALLATION

IMPORTANT INSTALLATION

SPECIFICATIONS

The installer should note that the appliance that
side walls should be no higher than the cooktop
itself.  Furthermore,  the  rear  wall,  the  surfaces
surrounding and adjacent to the appliance must
be able to withstand an temperature of 90 °C.
The  adhesive  used  to  stick  the  plastic  laminate
to  the  cabinet  must  be  able  to  withstand  a
temperature  of  not  less  than  150  °C  otherwise
the laminate could come unstuck.
The  appliance  must  be  installed  in  compliance
with the provisions in force.
This appliance is not connected to a device able
to  dispose  of  the  combustion  fumes.  It  must
therefore  be  connected  in  compliance  with  the
above  mentioned  installation  standards.
Particular  care  should  be  paid  to  the  following
provisions governing ventilation and aeration.

5) ROOM VENTILATION

It  is  essential  to  ensure  that  the  room  in  which  the
appliance  is  installed  is  permanently  ventilated  in
order  to  allow  the  appliance  itself  to  operate
correctly.  the  necessary  amount  of  air  is  that
required for regular gas combustion and ventilation
of  the  relative  room,  the  volume  of  which  must  not
be  less  than  20  m

3

. Air  must  naturally  flow  through

permanent  openings  in  the  walls  of  the  room  in
question.  These  openings  must  vent  the  fumes
outdoors and their section must be at least 100 cm

2

(see  fig.  3).  Construction  of  the  openings  must
ensure that the openings themselves may never be
blocked.  Indirect  ventilation  by  air  drawn  from  an
adjacent room is also permitted, in strict compliance
with the provisions in force. 

CAUTION: if the burners of the cooking top are
without  safety  thermocouple,  the  ventilation
outlet must have a minimum 200 cm² section.

6) LOCATION AND AERATION

Gas  cooking  appliances  must  always  dispose  of
their combustion fumes through hoods. These must
be connected to flues, chimneys or straight outside.
If  it  is  not  possible  to  install  a  hood,  an  electric  fan
can  be  installed  on  a  window  or  on  a  wall  facing
outside  (see  fig.  4).  This  must  be  activated  at  the
same time as the appliance (see fig. 5), so long as
the  specifications  in  the  provisions  in  force  are
strictly complied with. 

7) GAS CONNECTION

Before connecting the appliance, check that the
values on the data label affixed to the underside
of  the  cooktop  correspond  to  those  of  the  gas
and electricity mains in the home.
A label on the appliance indicates the regulating
conditions:  type  of  gas  and  working  pressure.
Gas connection must comply with the pertinent

standards and provisions in force. 
When  gas  is  supplied  through  ducts,

the

appliance  must  be  connected  to  the  gas  supply
system: 
● with a rigid steel pipe. The joints of this pipe must

consist  of  threaded  fittings  conforming  to  the
standards. 

● With  copper  pipe.  The  joints  of  this  pipe  must

consist of unions with mechanical seals.

● With  seamless  flexible  stainless  steel  pipe.  The

length  of  this  pipe  must  be  2  meters  at  most  and
the seals must comply with the standards.

When  the  gas  is  supplied  by  a  bottle,

the

appliance  must  be  fuelled  by  a  pressure  governor
conforming  to  the  provisions  in  force  and  must  be
connected:
● with  a  copper  pipe.  The  joints  of  this  pipe  must

consist of unions with mechanical seals.

● With  seamless  flexible  stainless  steel  pipe.  The

length  of  this  pipe  must  be  2  meters  at  most  and
the  seals  must  comply  with  the  standards.  It  is
advisable  to  apply  the  special  adapter  to  the
flexible  pipe.  This  is  easily  available  from  the
shops  and  facilitates  connection  with  the  hose
nipple of the pressure governor on the bottle.

● With  rubber  hose  pipe  in  compliance  with

standards. The diameter of this hose pipe must be
8 mm and its length must be no less than 400 mm
and no more than 1500 mm. It must be firmly fixed
to  the  hose  nipple  by  means  of  the  safety  clamp
specified by standards.

At  the  connection  end,  verify  the  gasproof  using  a
soap solution, never a flame.

WARNINGS:
-  remember  that  the  gas  inlet  union  on  the

appliance  is  a  1/2"  gas  conic  male  type  in
compliance with EN 10226 standards.

-  The  appliance  complies  with  the  provisions  of

the following EEC Directives:

CEE2009/142 regarding gas safety.

Summary of Contents for GD-Z01

















Reviews: